UHMWPE的例句大全

Ultra high molecular weight polyethylene pipe ( UHMWPE) has excellent properties of impact-resistance anti-corrosion abrasion-resistance self-lubricating non-toxicity and low temperature resistance.

超高分子量聚乙烯（UHMWPE）管道具有优异的耐冲击、耐腐蚀、耐磨损、自润滑、无毒和耐低温等性能，其寿命是普通钢管的7～8倍。

The acoustic emission feature of tensile fracture in UHMWPE/ LDPE is studied by means of testing in the paper.

本文试验研究了UHMWPE/LDPE复合材料拉伸破坏的声发射特性。

Study on acoustic emission feature of tensile fracture in uhmwpe/ ldpe(ⅰ)

UHMWPE/LDPE复合材料拉伸破坏的声发射特性研究（Ⅰ）

Meanwhile, a useful value for following study on tensile fracture mechanism of UHMWPE/ LDPE is given. The simplified formula of ultimate tension load is obtained in view of mix plastic-cone tension failure mode of the M10 plastic embedded part.

对后续研究UHMWPE/LDPE复合材料声发射特性和拉伸破坏机理具有参考价值。针对M10型预埋件的塑胶-锥体复合拉伸破坏形态，得出极限拉伸荷载的简化计算公式。

Effects of thermal history on the crystallinity and the melting points of UHMWPE

热历史对UHMWPE结晶度和熔点的影响

Thermal Properties Study on Treated UHMWPE Fiber for Surface Modifying

表面改性超高相对分子质量聚乙烯纤维的热性能研究

Effects of Sliding Velocity and Abrasive Materials on Wear Behaviour of UHMWPE and PTFE

滑动速度和磨料对UHMWPE和PTFE磨损的影响

The results show that the tensile strength of the UHMWPE fiber strands is greatly decreased when the temperature is higher than 123 ℃, and the ballistic absorption energy is up to the highest value when the molding pressure is about 12.5 MPa.

结果表明，温度超过123℃后拉伸强度有大幅的下降，而成型压力为12.5MPa时达到最大值。

Study on Abrasive Wear and Tensile Strength of Filler Reinforced UHMWPE Composites

填料改性UHMWPE基复合材料拉伸磨损性能的研究

Whereas, the friction coefficient and volume of wear scar of UHMWPE-ALN 1.0 wt% increased significantly. A lot of non-oriented loose fibrils accumulated on the worn surfaces of UHMWPE-ALN 1.0 wt% while some sheets-like peelings appeared on UHMWPE.

而UHMWPE-ALN1.0wt%的摩擦系数与磨痕体积有显著增加，微观形貌出现大量松散的无定向纤维，与UHMWPE表面的片状磨损有显著差异。

The surface of UHMWPE fiber was treated by plasma, liquid oxidization, crone and UV grafting. The morphology and oxygen content of the fiber surface were characterized by SEM and XPS.

本文用低温等离子、液态氧化、电晕、紫外接枝聚合等方法对UHMWPE纤维进行了表面处理，并用扫描电镜和XPS对纤维的表面形貌和含氧量作了表征。

The melt-spinning method has been used to produce high strength high modulus PE ( UHMWPE) fibres ( paraffin wax as diluent). This method remedies the defects of long production period and low efficiency of the gel-spinning method.

采用石蜡作稀释剂，用增塑熔纺的方法制备高强高模聚乙烯纤维（UHMWPE），弥补了传统凝胶纺存在的生产周期长、生产效率低的不足。

Ultrahigh molecular weight polyethylene fibers ( UHMWPE) of different gel concentration were prepared using gel spinning process followed by solvent extraction, drying and drawing.

采用凝胶纺丝工艺制备了具有不同质量分数的超高分子质量聚乙烯凝胶纤维，并对其进行了萃取干燥和后拉伸等处理。

Study on structure and property of UHMWPE fiber during super drawing

超拉伸过程中UHMWPE纤维结构与性能的研究

the decomposing temperature of complex of copper nitrate with 15-c-5 is over the processing temperature of uhmwpe, so it is used filling in uhmwpe.

15-冠-5与硝酸铜配合物的分解温度超过了UHMWPE的加工温度，决定用它对UHMWPE进行填充改性。

a tribological study on schiff base copper complex modifying uhmwpe and lubricants

Schiff碱铜络合物改性超高分子量聚乙烯及润滑油的摩擦学研究

Study on the formation mechanism of supermolecular structure of shish kebab s of gel-spun UHMWPE Fibers

超高分子量聚乙烯（UHMWPE）凝胶纤维串晶结构形成机理的研究

The results showed that HDPE ( 6098) was adequate to improve the UHMWPE processing property and the optimal ratio by weight of UHMWPE/ HDPE was 40/ 60 ( shortened form PE2 in this paper).

结果表明：采用HDPE（6098）与UHMWPE熔融共混，当配比为40／60时（文中简称PE2），共混合金的力学性能、加工性能最佳。

The preparation methods of two kinds of sliding blocks made from ultra high molecular weight polyethylene ( UHMWPE) composite and pure polytetrafluorethylene ( PTFE) powder were introduced respectively.

介绍超高分子量聚乙烯（UHMWPE）和聚四氟乙烯（PTFE）两款桥梁支座滑块的制备方法，并对滑块的性能进行了研究。

study on the friction and wear properties of uhmwpe/ sio_2 composite materials

UHMWPE/纳米SiO2复合弹性材料的摩擦磨损性能研究