bending test的例句大全

The bending properties of cement mortar externally bonded with carbon fiber reinforced plastics ( CFRP) sheets at different temperatures were studied by means of three-point bending test. The influences of temperature on the bending properties of CFRP-cement mortar were discussed.

用三点弯曲试验研究了水泥砂浆外贴碳纤维片材后在不同温度下的抗弯性能，探讨了温度对碳纤维增强塑料（CFRP）-水泥砂浆抗弯性能的影响。

The influence of nano-powder content in matrix and grain growth inhibitors on mechanical proper-ties and microstructure of modifying Ti ( C, N)-based cermets by nano-powder have been evaluated, using the means of three-point bending test and micrographic analysis.

用三点弯曲实验和显微分析评价了在基体中添加纳米粉和晶粒长大抑制剂对制备纳米粉改性Ti（C，N）基金属陶瓷的力学性能和微观组织的影响。

Based on the results of four-point bending tests of 14 RC test beams with different areas of CFRP strips, areas of steel tension bar and different lengths of CFRP, this thesis studies the flexural performance of the RC beams with near surface mounted CFRP strips.

本文对14根钢筋混凝土梁试件进行了四点弯曲加载试验，考虑加固量、纵筋配筋率和嵌贴长度的影响，重点研究了表层嵌贴CFRP板的抗弯加固承载力。

Obtained nanocomposite electrodeposition coatings rate is one times than electroless plating, look at micromorphology that the surface of nano-composite coating grow well, dense, uniform thickness, through the bending test and thermal shock test proved nano-magnesium alloy matrix composite coating have a good combination.

得到的电沉积纳米复合镀层的镀速比化学镀的镀速提高一倍，并且纳米复合镀层表面平整、致密、厚度均匀，通过弯曲、热震试验证明镁合金纳米复合镀层与基体结合良好。

In this paper, the distribution of biaxial bending strength and the influence of loading rate on fatigue strength in the biaxial bending test by use of soda-lime glass specimen with micro indentation crack are studied.

本文研究了带有微小压痕裂纹的钠钙玻璃试件在惰性环境中的双轴向弯曲强度分布和加载应力速率对试件疲劳强度的影响。

The slip between the threaded rod and concrete is little in the three-point bending test, indicating that the selected threaded rod and the torque applied to the nut before loading are acceptable in practical applications.

在加载过程中，螺杆与混凝土之间的相对滑移量很小，因此在拉拔试验中选择的螺杆以及施加于螺母的扭矩在实际工程中是适用的。

Firstly, the bending load-deflection relationship and failure modes of the test specimen were obtained by the four-point bending test.

首先进行静态四点弯曲实验，得到实验试件在静态弯曲载荷作用下弯曲载荷与加载点挠度的关系以及试件在静载作用下的破坏模式。

Biomechanical characteristics of femur were measured by three point bending test.

三点弯曲试验法测定骨生物力学；

The bond strength of the samples was measured by three point bending test.

采用三点弯曲法测试金瓷结合力，扫描电镜观察钛瓷界面。

The Web steel truss beam is simulated with three-dimensional beam element, and the equivalent bending rigidity of the beam could be obtained by bending test.

模型中，桁架柱采用三维梁单元模拟，其等效弯曲刚度利用弯曲试验直接获得。

Finally, through the flow test, Low-temperature bending test, Fatigue test, the result is modified mastic asphalt concrete road has an excellent performance.

最后通过流动性试验、贯入度试验、低温弯曲试验、疲劳试验得出改性浇注式沥青混凝土具有优良的路用性能。

The biomechanical properties of the healing radius were analyzed by a three point bending test.

桡骨的生物力学性能由三点弯曲实验所得的结果进行分析；

The load factor for 4-point bending test, whose derivation is usually not included in textbooks, is also derived in this paper.

简要地导出了一般教材上较少提及其推导的四点弯曲加载因子。

A special machine with scanning electron microscope ( SEM) used was designed for three point bending test.

设计了一种可用扫描电镜（SEM）动态观察、专门用于三点弯曲试验的特殊装置。

Mechanical properties were valued by high-temperature compress test, three point bending test and Vicker hardness test.

通过高温压缩试验、三点弯曲试验、显微维氏硬度试验等评价合金的机械性能。

This paper engages in research on bending failure characteristic and resistance to rutting of grid asphalt concrete with the same material and gradation but different reinforcement pattern by bending test and rutting test.

通过弯曲试验和车辙试验，对材料与级配相同情况下不同加筋方式的格栅沥青混凝土的弯曲破坏性能和抗车辙能力进行了研究。

The validity of the tibia segment model was evaluated against three point bending test in terms of tibia stress.

胫骨模型由胫骨三点弯曲应力分析实验验证。

At present, tuning-folk resonance plate structure is common used in crankshaft bending fatigue test bench in domestic diesel engine industry.

目前，国内柴油机行业普遍使用的曲轴弯曲疲劳强度试验台架，均采用音叉共振板结构。

Samples of hot rolled steel plate Q235 in various specifications having cold bending cracks are examined by means of Metallographical test and electron probe analysis.

对不同规格的Q235热轧钢板冷弯裂纹试样进行了金相检验和电子探针等分析。

Thus continuing the regular measurements of the bending curves of the test-piece, one could construct a creep curve.

如此继续进行试件的挠度观测，就可绘制出蠕变曲线。