bonding strength的例句大全

Study on the bonding strength of the adhesive with low viscosity for building

工艺参数对低粘度建筑结构胶粘接强度的影响

The thermocompression wire bonding strength was tested with bonding tester. The strength was over 0.17 N.

使用接合强度测试仪对压焊键合点强度进行了拉断试验，测得键合强度拉断力都在0.17N之上。

Comparison of Different Cements on Bonding Strength of Titanium Dowel

不同粘接剂对钛桩粘接强度的比较

Testing Surface Bonding Strength for Thin MDF

薄型中密度纤维板表面结合强度的测试

The effect of bonding time on the bonding strength of thick aluminum wire wedge bonding was studied under different ultrasonic power conditions.

试验研究了不同超声功率条件下，键合时间对粗铝丝引线键合强度的影响规律。

The bonding strength of the samples was measured by a three-point bending test.

采用三点弯曲试验测量钛与瓷的结合强度。

The bonding strength of Ti/ porcelain was evaluated using three-point bending test according to ISO 9693 1990 standard.

根据ISO9693标准，对钛/瓷间的三点弯曲结合强度进行测试，并对钛/瓷结合界面进行SEM观察。

After HF acid etching under 5 different HF concentrations and 6 exposing times, shear bonding strength of porcelain to enamel were tested.

选择30个氢氟酸（HF酸）浓度－时间搭配点，测试瓷贴面复合体整体粘结抗剪强度。

Structure and Property and Bonding Strength of Titanium Carbonitride Coating

氮碳化钛涂层的结构性能及结合强度

This investigation is to determine the effect of temperature on bonding strength, impedance and power of PZT transducer in thermosonic bonding process.

在有规律地改变键合温度的条件下，分析不同温度对热超声键合工艺连接强度的影响规律，并研究温度因素对整个系统的PZT换能器输入功率及阻抗的影响。

Thermal Stability and Bonding Strength of Hydroxyapatite/ zirconia Composite Coatings

羟基磷灰石/氧化锆复合涂层热稳定性和结合强度的研究

Effect of thermal spray process on bonding strength of aluminum coating on glass surface

热喷涂工艺对玻璃表面铝涂层结合强度的影响

It is found that particle and substrate preheating can promote the occurrence of thermal softening effect, and then enhance the plastic deformation and final bonding strength between particles and substrate.

研究结果表明，预热处理可以促进粒子或基体发生热软化效应，进而促进强塑性变形的发生，同时提高接触面附近的局部温度，促进粒子与基体的结合。

The bond exhibited typical glass phase with low melting temperature and high bending strength of strips ( 53.62-93.34MPa). The microstructure analysis indicated the enhancement of the bonding strength resulted from the chemical reaction between the vitrified bond and microcrystal alumina ceramic.

结合剂为典型玻璃相，熔融温度较低，试样抗折强度为53.62-93.34MPa，微观分析表明两者间发生了化学反应，增强了结合剂对磨粒的把持力，提高了磨具的强度。

The effect of reaction phase on bonding strength was also discussed.

分析了反应相对接头强度的影响。

But when the temperature too high ( 1473K), the thickness of VN reaction layer and the bonding strength of joint both decreased.

但是当温度过高，达到1473K时，反应层厚度降低，接头的性能下降。

It was found by TEM that some new phases exist at the interface after the thermal cycling treatment by 1000 times, and it is considered that this kind of interfacial reaction made the interface bonding strength decreased.

透射电镜观察结果表明，经1000次热循环后，复合材料界面处出现一些新相，破坏了循环处理前良好的界面结合。

During the welding process of titanium alloy and aluminum alloy, it is easy to form many kinds of brittle intermetallic compounds at the interface of Ti/ Al dissimilar alloys. Those compounds weak the bonding strength of Ti/ Al joints.

钛合金和铝合金的焊接过程中，在Ti合金/Al合金界面处极易生成各种脆性的金属间化合物，制约着接头的结合性能。

It is shown that the effect of interphase thickness on thermal expansion of 3D-C/ SiC composites lies in its influence on interphase bonding strength and sliding resistance in the debonding layer.

结果表明：①界面相厚度对3DC/SiC复合材料热膨胀性能的影响主要归因于其对界面结合强度和脱黏面上的滑移阻力的影响。

Study on Bonding Strength Between Self-made Metal Stub and Vita Mark ⅱ Ceramic Block

自制金属底座与VITA MARKⅡ瓷块粘结强度的研究