bonding strength的例句大全

Comparison of Different Cements on Bonding Strength of Titanium Dowel

不同粘接剂对钛桩粘接强度的比较

Study on the bonding strength of the adhesive with low viscosity for building

工艺参数对低粘度建筑结构胶粘接强度的影响

Of process parameters on the bonding strength of coating from the primary to the meeting were: spray distance, atomization air pressure, spray voltage, spray current.

工艺参数对涂层结合强度的影响由主到次依次为：喷涂距离、雾化空气压力、喷涂电压、喷涂电流。

The reflectance of the black coatings, the thickness of which can reach 25 μ m, can be as low as 7%, and the bonding strength between the black coating and the matrix can be as high as 234 MPa.

发黑膜对光的反射系数最低可达7%，厚度可达25μm，与基底的结合力达234MPa以上。

Effect of thermal spray process on bonding strength of aluminum coating on glass surface

热喷涂工艺对玻璃表面铝涂层结合强度的影响

The effect of bonding time on the bonding strength of thick aluminum wire wedge bonding was studied under different ultrasonic power conditions.

试验研究了不同超声功率条件下，键合时间对粗铝丝引线键合强度的影响规律。

This showed the catalytic activity of perovskite-type oxides well associated with the B-O bonding strength of the oxides active renter.

说明钙钛矿型复合氧化物的催化活性与体系活性中心的B&O键合作用能力有关。

The morphological structure analysis indicated that PE-g-MAH addition decreased the surface tension, making the two phases disperse uniformly, enhancing the bonding strength of interface and improving the compatible property of nylon 11 and PE.

形态结构分析表明，接枝物的加入，降低了界面间的表面张力，使两相分散均匀，分散度提高，增强了相间的粘接力，改善了尼龙11与聚乙烯的相容性。

The bond exhibited typical glass phase with low melting temperature and high bending strength of strips ( 53.62-93.34MPa). The microstructure analysis indicated the enhancement of the bonding strength resulted from the chemical reaction between the vitrified bond and microcrystal alumina ceramic.

结合剂为典型玻璃相，熔融温度较低，试样抗折强度为53.62-93.34MPa，微观分析表明两者间发生了化学反应，增强了结合剂对磨粒的把持力，提高了磨具的强度。

The effects of rolling temperature, pass reduction on the interfacial bonding strength were researched; and the effect of the subsequent annealing process on the interfacial bonding strength and the joint interface structure were investigated.

研究了轧制温度、压下率对复合板的结合强度的影响，以及轧后退火工艺对复合板的结合强度及界面结构的影响；探讨界面结合机理，确定出最佳工艺方案。

In this study, according to the design of increasing bonding strength between interlayers, phlogopite type calcium mica glass ceramic has been developed.

研究根据提高云母层间结合强度的构想，研制以钙云母为主相可切削微晶玻璃。

A Study on Bonding Strength of Hybrid Integrated Circuits

功率混合集成电路键合强度控制研究

The relationship of bonding strength and temperature are investigated.

分析了键合强度与键合温度之间的关系。

Research progress in the effect of different porcelain conditioning techniques on bonding strength

极限黏结力〔土地〕不同瓷表面处理方法对托槽与瓷面黏结性能影响的研究进展

A New Model For Determining the Interface Bonding Strength in Layered Composite Materials

确定层状复合材料界面结合强度的新模型

Influence of contact pressure to bonding strength between fiber sheets and concrete

接触压对纤维布与混凝土粘结强度的影响

Interface Bonding Strength of Composite White Cast Iron Embedded Steel Bar

加筋复合白口铸铁界面的结合强度

On-Line Examination Method of Bonding Strength Measurement in Silicon MEMS Devices

硅MEMS器件键合强度在线检测方法

Effect of ultrasonic power on the wire bonding strength

超声功率对引线键合强度的影响

Some suggestions on construction are presented from the angle of bonding strength.

最后从新旧混凝土的粘接强度的角度讨论了后浇带的施工问题。