contact angle的例句大全

Experiment principle was based on the porous plug when penetrative liquids went into the powders. The contact angle between the liquid and the powder was calculated by applying Washburn equation into the flow of the liquid in capillary.

实验原理建立在把渗透的液体进入玻璃管内粉末形成的多孔塞基础上，将Washburn方程用于毛细管内液体的流动用于计算液体和粉末之间接触角大小。

A hydrophobic index and the relative contact angle in the hydrophobic and wetting experiments were employed to evaluating modification results. The relative contact angle of the aqueous solution on the silica gel powder has been obtained by modified Washburn method.

用改进的Washburn方法测定16-2-16水溶液在硅胶粉末表面的接触角，并进一步讨论了16-2-16在硅胶表面的吸附引起的润湿性变化。

Factors that effect the preciseness of contact angle measurement are the roughness of the solid surface. The change of temperature and equilibrium time effect the contact angle slightly.

影响接触角法测定准确的主要因素为表面粗糙度，此外温度变化及平衡时间对接触角也略有影响。

Contact angle: The angle made by a drop of liquid with a solid at the point of intersection.

接触角：一滴液体和固体接触时所造成的角度。

The relationships of the graft efficiency ( GE) and contact angle(θ) with the conditions of graft copolymerization of PP filter material for cigarette were studied.

研究了香烟滤材聚丙烯（PP）化学接枝共聚条件与接技率（GE）和表面接触角（θ）之间的关系。

Contact angle and XPS were employed to evaluate grafting effects.

并通过接触角、XPS等方法对接枝效果进行检测。

The contact angle, activation rate and oil absorbency all increased in various degree.

改性后的滑石粉接触角、活化率、吸油率都有不同程度的提高。

The property changes of foam rubber surface before and after the treatment were studied by XPS and contact angle measurement.

通过X射线光电子能谱分析和接触角测定，研究了处理前后泡沫橡胶表面性质的变化。

Simulate the water film formation conditions at the time of tillage parts touching soil, tested the optimal combination of etching Plowshare Steel surface contact angle.

模拟耕作时触土部件形成的水膜条件，测试了刻蚀的最优组合的犁铧钢表面的接触角。

The gravitational thermal analysis, machine intensity analysis and contact angle determination were employed to characterize the performance of Polyvinylidene Fluoride membrane after hydrophilic modification.

用热重分析、机械强度分析和接触角测定对亲水改性后的聚偏氟乙烯膜进行了表面性能表征。

The optimum contact angle is 119.1 ° for the droplet with radius 1 microns.

液滴半径等于1微米时，适宜接触角为119.1度。

Contact angle measurement indicates modified membranes are more hydrophobic and of higher benzene solubility than unmodified one.

接触角测量结果表明，改性膜的亲苯性和疏水性均增强。

The variation of the line tension came from deformation of droplet, which was an important factor to determine the accuracy of measuring contact angle.

结果表明，由液滴形变作用引起的线张力变化是影响接触角测量准确性的一个重要因素。

with the increase of graft yields gradually, the surface contact angle of fabrics increased correspondingly and showed the trend of a gradual slowdown. when the grafting yield reached a certain value, if it is further increased, the contact angle will decrease.

随着单体接枝率的逐渐升高，织物表面接触角逐渐增大，但趋势逐渐放缓，当接枝率过高时，反而会使接触角下降。

The hydrophobe experiments show DLC films by PECVD method have the highest contact angle ( about 90 °) and the lowest surface energy.

憎水性能测试表明，化学气相沉积法DLC膜的接触角（90°左右）最高，具有最低的表面能；

It was found by calculation that thrust load has an evident effect on contact angle while radial load influence feebly, clearance has a great impact on load distribution and appropriate interference fit increases carrying capacity, but the maximum needle burthen also increases.

计算结果表明，角接触球轴承的轴向载荷对工作接触角影响明显，而径向载荷影响很小；游隙对滚针轴承载荷分布的影响很大，适当过盈可提高承载力，但滚针最大负荷增大。

The wetting agent can change the wetting contact angle of the solid surface, the ideal condition for the solid phase is oil-water neutral wettability, the state of the emulsion show more stability.

润湿剂能改变固相表面的润湿接触角，当固相为理想的油水中间润湿时乳状液的稳定性能最好。

A method is investigated to analyze the physical feature of a drop, such as surface tension, contact angle and volume through fitting contour of the drop picture.

本文研究了利用照相机捕捉到的液滴灰度图像，分析求取液滴的表面张力、接触角、体积等物理参数的方法。

The wetting ability of chitosan solution on the olefin medium was poor and the contact angle between chitosan solution and olefin was 105 °.

壳聚糖溶液在蜡质界面上润湿性差，界面接触角为105°。

Contact angle is applied as a boundary condition at the liquid-solid contact line.

接触角作为液-固接触线处的边界条件输入模型。