contact paper的例句大全

This paper introduces the engineering practice of treating synthetic detergent wastewater through coagulating sedimentation, biochemical treatment, contact filtration and adsorption processes.

介绍了混凝沉淀生化处理接触过滤活性炭吸附工艺处理合成洗涤剂生产废水的工程实践。

In this paper, to avoid the current-contact measurement of the drawbacks, a laser Doppler Effect based on the non-contact cable length measurement is used.

本文针对现行接触式测量所存在的弊端，采用了一种基于激光多普勒效应的非接触式电缆长度测量方法。

This paper introduced a system for electric parameters testing of contacts of AC contactors realized by microcomputer, analyzed measure principle of contact resistance and temperature rise of contacts of AC contactors, and stated hardware structure and software flow of the testing system.

介绍了一种用微机实现的交流接触器触头电参数测试系统，分析了交流接触器触头的接触电阻和温升的测量原理，简述了测试系统的硬件结构和软件流程。

This paper points out the disagreement of boundary conditions that generate force discontinuity in the linear spring damping contact model by analyzing the contact modulation of the clearance joint.

分析了含间隙运动副副元素的碰撞分离过程，指出线性弹簧阻尼模型不能满足接触边界条件并产生力突变；

Through structural analysis of traditional semi-rigid base course asphalt pavement which appears water damage, the paper reach the conclusion that water has an effect on material design parameter and pumping leading to the change of contact condition are the main factors.

通过对传统的半刚性基层沥青路面出现水损破坏进行结构分析，得知水对材料设计参数的影响和由于唧浆现象导致路面结构层层间接触条件的变化是沥青路面出现水损破坏的主要原因。

A novel non-contact type low current sensor with multivibrator composed of single nanocrystalline core and double-winding is presented in the paper.

利用纳米晶合金材料作为敏感材料，提出了采用单纳米晶磁心双绕组结构、多谐振荡桥励磁的对微电流进行非接触测量的新型电流传感器。

This paper introduces the electronic relay that can controns the thermogenic element without point of contact in constant system, gets continous power and compensates voltage by automation.

介绍了一种电子继电器，具有对恒温系统中加热元件的无触点控制和无级设定功率，以及自动适应电压变化的补偿功能。

In this paper, the contact reaction between Aluminum and Copper and its liquid phase behavior were studied by means of experiment simulation and analysis based on the theory of surface and grain boundary diffusion in metallurgy.

采用模拟的方法，系统研究了Al/Cu接触反应及其液相行为的特点，并运用金属学中表面扩散和晶界扩散等理论进行了理论探讨。

this paper expatiated the basic process of testing the deformation quantity of a material during stretching process by using linear ccd sensors in non-contact mode.

阐述了用线阵CCD传感器对材料拉伸变形量进行非接触测试的基本过程。

A 3D solid friction contact method is applied in this paper. Stiffness matrix of contact element has been presented, and the contact force and friction force between friction contact pairs of nodes are calculated too.

接着从理论上进行了三维实体摩擦接触问题的分析，推导了三维实体摩擦接触单元的刚度矩阵，计算了三维实体摩擦接触对中的接触力和摩擦力。

This occurs if the paper surface is rough and cannot mae contact with the gravure cells.

原因是纸面粗糙，不能与版上的凹陷印纹接触所致。

In this paper, the drum-shaped roller, which is a key element of a new-type reel coupling of drum-shaped roller for the use of crane, was analysed, using the contact strength mothod. The practical example of calculation is made.

本文对起重机专用新型联轴器鼓形销卷筒联轴器的关键零件鼓形联接销按接触强度进行了应力分析，并作了实例计算。

As the break capability of aerospace relay contact will be different at different load, the paper studys on the arc shape change while changing the load. And it draws some conclusions on the arc burning.

由于航天继电器触点对不同性质负载的切换能力不同，本文对不同负载下的电弧形态进行了研究，总结出电弧燃烧的一些规律。

Finally, the paper gives the rules for judging failure types of relay after introducing the contact state recognition.

最后，本文给出了引入识别系统后更加可靠的继电器失效类型的判定方法。

Analysis of these experimental data, the printability of paper with different properties, derived properties and printability of paper in close contact.

通过这些试验数据分析研究不同性能的纸张的印刷适性，得出纸张的性能和印刷适性的密切联系。

The paper is focused on manufacturing and application technology of diamond dressing contact roller with some application examples of domestic man made diamond dressing contact roller to blade groove machining of air turbine engine.

文章着重介绍了金刚石修整滚轮的制造和应用技术，并例举了国产人造金刚石修整滚轮在气轮发动机叶片之叶根榫槽加工中的应用实例。

Finally, the paper will describe the difference and the contact of the three major network optimization method, and look into the future of network optimization on the basis of the previous analysis.

论文的最后，在前面分析归纳的基础之上，阐述三大网络优化方法之间的的区别与联系以及自己对网络优化未来的展望。

In this paper, by the contact has between BCK-algebra and axiom system of cubic lattices. The M-R open problem on infinite cubic lattices is answered in the affirmative.

在本文中，通过关联BCK-代数与立体格公理系统的联系，给出了M-R公开问题一个肯定的答复。

This paper derives, under small deformation assumption, elastic theory solutions for axisymmetric plane stress for pinch contact deformation between a plate containing a hole and an axle that differ from existent documents.

按小变形假定，导出了与现有文献不尽相同的孔体与轴过盈接触变形的轴对称平面应力弹性解；

This paper describes main failure mechanism for MOS VLSI, Thin oxide breakdown, hot carrier effect, Al-Si contact failure, electromigration and soft errors. It gives out some technical measures to prevent above-mentioned failures.

本文论述了MOS VLSI主要失效机理，即薄氧化层击穿、热载流子效应、铝－硅接触失效、电迁移以及软错误，并给出了预防上述失效的一些技术措施。