curing time的例句大全

The improvement of peroxide crosslinked EPDM properties with trimethylolpropane triacrylate ( TMPTA) was studied. It was found that the crosslinking rate and crosslinking density increased and the curing cycle time reduced with the addition of TMPTA in the peroxide crosslinking system for EPDM/ silica compound;

在EPDM／白炭黑胶料的过氧化物硫化体系中，加入三羟甲基丙烷三丙烯酸酯（TMPTA）能够迅速提高硫化胶的交联效率，增大网络密度，缩短硫化时间；

Conclusions: Shenmai injection combined with composite salvia miltiorrhiza injection in curing shock is able to significantly improve the curative effects, shorten the time of recovery and meanwhile effectively reverse and restrain the development of shock.

结论：联用参麦注射液和复方丹参注射液治疗休克能明显提高疗效，缩短病程，逆转和阻断休克的发展。

Use TG to investigate heat-resistant quality of MUF resin, and the effect of curing agent, storage time, sample state on that was mainly studied.

采用热重分析法（TG）对MUF共缩聚树脂的耐热性能进行评价，重点比较了固化剂、贮存时间、样品状态等条件对MUF树脂耐热性能的影响。

The relations between the time of surface drying and the quantity of curing agent was established.

测定了固化剂用量与涂膜表干时间的关系，表干时间随固化剂用量的增多而减短。

The effects of different lasting time and humidity conditions during the crucial temperature phase in the flue-cured tobacco curing on the aroma were studied by using the electric-heated temperature and humidity auto-controlled flue-curing barn supplied by Henan Agricultural University;

采用河南农业大学自行研制的温湿度自动控制烤烟箱，针对烟叶烘烤过程中的几个关键温度段，探讨了不同湿度和不同停留时间对烟叶质量的影响；

A study was made on concrete creep under different curing temperatures, and the comprehensive effects of time and temperature on creep development were expressed with the chemical reaction rate.

对不同养护温度下的混凝土徐变进行了研究，用化学反应速率描述温度对混凝土徐变的影响。

This may be done in a reciprocating screw machine where one charge at a time is brought to curing temperature.

这可能是在做往复螺杆机，其中一名主管在一个时间是带来的固化温度。

The results showed that the test temperature had certain influence on the Mooney viscosity, Mooney scorch time and curing behavior of rubber compound;

结果表明，试验温度对胶料的门尼粘度、门尼焦烧时间和硫化特性均有一定影响。

substrate envirogluvtm munltivariable affect net-point quality, at the same time also affects the ink curing fast and slow.

承印物上的油墨厚薄会影响网点的质量，同时也会影响油墨的固化快慢。

besides the scorch time and optimum cure time of biir were shortened considerably while its curing rate increased obviously.

与丁基橡胶相比，BIIR焦烧时间和正硫化时间明显缩短，硫化速度大大提高。

The key consideration and the pouring temperature of the concrete under low temperature construction, curing temperature, heat storage and holding time parameters on the maximum temperature rise inside the concrete, as well as the size of the surface tensile stress, and draw some useful conclusions.

重点考虑和阐述了混凝土在冬季施工下的浇注温度、养护温度、蓄热保温时间等参数对混凝土内部最高温升以及表面拉应力大小的影响，得出了一些有益的结论。

Through above experiment, it would be expected to shorten port wine stain cure time and use them in curing degeneration of macula.

通过上述实验，试图缩短鲜红斑痣的治疗时间，另外期望在需更强的杀伤效应的光敏剂才能完成的老年黄斑变性的治疗方面能得到应用。

Results: There is a great significance of cure rate and curing average time between observation group and tradition medical group ( P < 0.01).

结果：角膜解毒剂较西医传统疗法治疗单纯疱疹病毒性角膜炎，角膜刺激症状及溃疡愈合情况观察组明显高于对照组，治愈率差异有显著性（P

Methods 202 medical records of curing esophageal cancer from January 1996 to December 2004 in our hospital were collected and their age, sex, inducement of falling ill. the time from falling ill to be in hospital, method and prognosis were registed.

方法收集1996年1月至2004年12月食管癌治疗的病历共202例，分析其年龄性别、患病诱因、从起病到住院治疗时间、治疗方法及其预后。

In order to simultaneously recycle waste rubber powder and fiber and solve shock resistant performance problems of the unsaturated resin after curing, the first time the unsaturated polyester/ waste rubber powder/ tires fiber composites were raised and prepared in this study.

为了同时回收利用废胶粉和废纤维，解决不饱和树脂固化后硬而脆、耐冲击性能差的问题。

by increasing uv radiation intensity, uv curing rate and double bond conversion rate of composite system were significantly increased, the tack free time was shortened at the same time.

增大紫外光辐照强度可显著提高复合体系的光固化速率及双键转化率、缩短表干时间。

Then, it makes target mixture proportion design to study on the aggregate gradation scope, optimum asphalt content of mixture, the temperature and time of curing.

然后，对确定配合比例的国产环氧沥青进行混合料目标配合比设计，确定了矿料的级配范围、混合料的最佳油石比以及高温固化温度、时间等参数。

The ideal exposure depends on your screen after curing made from grade 7 time gray-scale.

抱负的曝光取决于在丝网制成后固化7级灰量所需给的工夫.

Time of temperature rising during slurry curing depends on motor size.

发动机尺寸愈大，固化升温时间愈长。