inlet temperature的例句大全

Based on the designed thin film evaporator, the influence of the rotor speed, feed rate and liquid inlet temperature on evaporation length and film heat transfer coefficient was primarily discussed using the software CFX 4.4 with water as feed liquid.

针对自行设计的薄膜蒸发器，以水为物料，采用大型CFD软件CFX4.4，初步探讨了刮板转速、进料量、进料温度等参量对薄膜蒸发器蒸发段长度和加热段膜内传热系数的影响。

It is shown from the results that the inlet temperature rise just prior to system instability is approximately linear with the inlet temperature ramp rate.

数值结果表明，引起失速的进口温升近似地与进口温升率呈线性关系。

Fresh inlet temperature range which satisfies given error limits is achieved, and the effect of instrumentation precision on accuracy of test results is analyzed by calculating and analyzing uncertainties of sensible effectiveness tests.

通过对显热效率测试的不确定度的计算与分析，得出了满足给定误差限的新风进口温度范围，并分析了仪表精度对测试结果准确度的影响。

Moreover, static flow instability ( flow excursion) is also observed to occur for some conditions of low inlet temperature.

此外，在加热段入口温度较低时，亦可能在流量陡降区发生静态流动不稳定性（流量漂移）。

The world vertical upward flow round critical heat flux experimental database is analyzed based on the slice method, similarity measure, heat balance and inlet temperature verification.

采用切片法、相似度概念和热平衡以及进口温度检验法，对收集到的圆管垂直向上流动临界热流密度实验数据库进行了分析。

The calculation results show that temperature drop under fixed gas inlet area is more than that under unfixed gas inlet area.

计算结果表明，固定燃气入口面积较不固定燃气入口面积对燃气的降温量大；

The temperature at oil inlet at the bottom of the fractionating tower in one catalyzing cracking workshop was increased from original designed value 480 ℃ to 525 ℃, therefore, the safety of the equipment when operating at over-temperature need to be analyzed.

某炼油厂催化裂化车间分馏塔下部油气入口温度由原设计的480℃提高到525℃，因此需对其超温运行的安全性进行分析。

Low speed low inlet velocity, the bearing temperature is relatively high, the relatively high speed high inlet velocity, the bearing temperature is relatively low.

低转速低入口流速时，轴承温度相对比较高，相对高转速高入口流速时，轴承温度相对较低。

Analysis of Uneven Temperature Distribution at Inlet of Centripetal Type Radial Bed Converter

氨合成塔向心型径向床中进口温度分布不均匀的分析

Displacement Ventilation for Three Heat Sources: Influence of Inlet Air Temperature

送风温度对三个污染源置换通风效果影响研究

And inlet air temperature is 160 ℃.

乳化剪切时间为12min、进风温度为160℃。

Simultaneity, effects of different inlet air velocity 、 temperature and quality ratio of CH4/ O2 on reactants and resultants in chemical looping fluidized bed has been investigated.

同时，研究了不同进口气体速度、温度和CH4/O2的配比对化学链流化床内反应物与生成物的影响。

The influences of the inlet diameter, overflow diameter, underflow extension pipe length, split ratio, feed flowrate and temperature on the separation performance are analyzed.

探讨了溢流分率、溢流口直径、进料浓度、入口直径、尾管长度、进料流量及温度等对旋流器分离性能的影响。

there are small temperature and pressure difference in steam inlet and outlet of heat exchanger, and big heat transfer surface.

换热器蒸汽入口和出口温差小，压差小，管程传热面积大。

The influence of inlet air temperature on two-phase flow was analysised.

并通过不同进口温度下的计算，分析了热态两相流场和喷雾场在不同进口温度下的变化。

A stagnation pressure and stagnation temperature were set at the pipe inlet.

在管路的进口处，给定总压力和总温度。

While the effect of engine speed on the required inlet air temperature for autoignition is different for different octane numbers.

而发动机转速对自燃所需进气温度的影响则随所用燃料辛烷值的大小而异。

A Study on Precooling Mine Inlet Airflow By Utilizing the Low Temperature Effect of Terrain

利用岩层的低温效应预冷矿井入风流的研究

The results show that the increment of oxidizer inlet expansion is favorable for efficiency and stabilization of the motor, and the increase of length of the afterburning chamber can raise the average burning temperature and improve the combustion efficiency.

结果表明，增加氧化剂入口突扩段有利于发动机稳定工作和充分燃烧，增加补燃室长度可以提高发动机平均燃烧温度，使燃烧更加充分。

The nozzle throat diameter was 35 mm, and the inlet stagnation temperature and pressure were 800 K and 274 4 kPa, respectively.

主喷管喉道直径为35mm，进口总温和总压分别为800K及274.4kPa。