liquid alloy的例句大全

Problems: The primary stress to which the surface of the mould is exposed are thermal shock, abrasion and chemical reactions between the liquid alloy and the iron in the steel mould.

问题：压铸模具表面主要面临的问题有热冲击、磨损、液态合金与模具钢的化学反应等。

During the solidification process of Al Fe alloy under centrifugal casting, the primary phase migrates along the radius because of the density difference between the primary phase and the liquid alloy. Therefore the distribution of the primary phase is in gradient along the radius of the casting.

离心铸造Al Fe合金凝固过程中的先析出相与合金液之间具有较大的密度差，在离心力场作用下，先析出相将沿径向由内向外迁移，致使初生相沿铸件径向呈梯度分布。

A Thermodynamic Criterion for Judging Symmetry of Liquid Alloy Systems and Its Application to Geometrical Models

几何模型应用于液态合金时体系对称性的一个热力学判据

A thermodynamic criterion for identifying the symmetry of ternary liquid alloy systems with regular solution is described.

结果表明，采用正规溶液模型作为判断实际体系对称性的热力学判据是方便可靠的。

Distortion of PIM tungsten heavy alloy during liquid phase sintering

PIM高密度合金在液相烧结过程中的变形

The density of tungsten heavy alloy plates liquid phase sintered in continuing furnace was investigated with drainage, and its distributions both in width and length were studied.

采用阿基米德排水法，测量了连续液相烧结钨基高比重合金板的密度，并对其在长度和宽度方向上的密度分布进行了研究。

Fractal analysis on temperature-induced discontinuous structural change of the liquid in-80% sn alloy

温度诱导液态In-80%Sn合金结构非连续变化的分形分析

Al-Cu-Ni ternary alloy powders were fabricated with a new solid-liquid reaction milling technology.

利用固液反应球磨技术制备了Al-Cu-Ni三元合金粉末。

Tensile Fracture Morphology of As-cast 7005 Aluminum Alloy Produced by Electrolytic Liquid Al

电解铝液制备的7005铝合金铸态拉伸断口分析

The reaction model of ternary alloy solid-liquid reaction technique was developed on the basis of the collision-peeling model.

在固液反应球磨的整体模型，即打击一剥落反应模型的基础上，提出了三元合金固液反应球磨的模型。

The Deposition of Tb-Fe-Co Ternary Alloy from Ionic Liquid

离子液体电沉积Tb-Fe-Co三元合金的研究

Liquid Ag-38.5 Cu-33.4 Ge-28.1 ternary eutectic alloy was undercooled by a great degree up to 175 K ( 0.22 T-E).

在Ag38.5Cu33.4Ge28.1三元共晶合金的深过冷实验中，获得的最大过冷度为175K（0.22TE）。

Fabrication of Al-Cu-Co Ternary Alloy Powders By Means of Solid-liquid Reaction Milling

固液反应球磨制备Al-Cu-Co三元金属间化合物

The influence of liquid steel on the formation of compacted chromite coating at high temperature has been investigated by pouring a test block of alloy steel casting as well as by scanning electron microscopic observation and electron microanalysis.

通过浇注合金钢铸件试块并借助电子显微镜观察和X－Ray分析，研究了钢液对铬铁矿高温致密涂料层的影响.结果表明：涂层的致密度与钢液作用的激烈程度成正比关系；

This paper studies the effect of thermodynamic factors, including temperature, pressure and chemical compositions, on the solubility of nitrogen in liquid ferroalloy. In the condition of suitable chemical compositions of alloy, increasing nitrogen pressure can obviously promote the solubility of nitrogen.

从温度、压力、合金成分3个方面研究了影响氮在液态铁合金中溶解度的热力学因素，发现合金钢成分合适时，增大系统的氮气分压可以明显地提高氮的溶解度。

Measurement and calculation of specific heat for a liquid Ni-Cu-Fe ternary alloy

液态三元Ni-Cu-Fe合金比热的实验与计算研究

Characteristics and process of thermotropic liquid crystal polymer alloy

热致性液晶聚合物合金的性能与加工

Characteristics and Application Prospect of Thermotropic Liquid Crystal Polyester/ Thermoplastic Alloy

热致液晶聚酯&热塑性塑料合金的性能和应用前景

It reviewed epoxy toughened by resin alloy, and discussed several new technologies of toughening epoxy such as modified by thermoplastic resin, thermotropic liquid crystal polymer and IPN.

综述了环氧树脂的树脂合金化增韧改性，着重讨论了热塑性树脂、热致液晶聚合物和互穿网络结构等环氧树脂增韧改性新技术。

Electrochemical corrosion occurred under the thin liquid film is the essential of high-strength aluminium alloy atmospheric corrosion.

高强铝合金大气腐蚀的本质是表面薄液膜覆盖下的电化学腐蚀。