mark position的例句大全

please also mark position applied on envelope. photos and resumes will not be returned.

也请为在信封上被应用的位置作标记。

please mark position that you are applying for on the envelope.

邮编请在信封上注明应聘职位。

please send full resume with current and expected salary to the following address. please also mark position applied on envelope.

请将目前为止全面的简历和期望的薪水寄至以下地址。

the maximum limit of bytes that can be read before the mark position becomes invalid.

在标记位失效之前可读取的最大字节数。

if original clutch cover will be reinstalled, mark position of cover on flywheel for assembly references paint or scribe for this purpose.

如果安装原来的离合器盖板，在飞轮上标记盖板的位置，以便于参考。用油漆或划线来完成此工作。

Chapter 2 mainly illustrates the important position of the Chinese Confucius Temple in Chinese traditional culture, and tries to carry on a research on the property of culture mark and culture symbol.

第二章主要探讨了中国文庙在中国传统文化中的重要地位，并试图将其作为一种文化象征和文化符号进行研究。

Mark pistons in installation position using a water-resistant marker.

使用防水记号笔在安装位置上标记活塞。

Accounting treatments vary-HSBC carries its investments at cost, while broker-dealer Goldman Sachs must mark its position to market.

会计处理方法差别很大——汇丰（HSBC）按成本价计算投资，而经纪商兼交易商高盛（Goldman Sachs）必须按市价来记入其持有的股票头寸。

Mark installation position with a strip of adhesive tape.

用一条胶带标记安装位置。

In the end, mark out three prospecting objects of available lithology-structure compound trap and designate the next proposal exploring well position combined with the result of seismic muti-attribute reservoir forecast.

结合地震多属性油气预测结果，划分出了潍北东区块三个有利岩性-构造复合圈闭的勘探目标及下一步的勘探建议井位。

When installation, and without holing can easily move installation position, moves won't injure metope, also won't leave a mark on walls.

安装时无须打孔，且能方便地移动安装位置，移动时不会损伤墙面，也不会在墙面留下痕迹。

Mark the installation position with a paint marker before removing the fuel level sensor.

拆卸燃油油位传感器之前，用油漆标志标记安装位置。

TAKE A CLEAR-CUT STAND AGAINST BOURGEOIS LIBERALIZATION flagpole used to mark the position of the hole on a golf green.

旗帜鲜明地反对资产阶级自由化高尔夫场地中标志球的位置的旗杆。

Please mark your position in the organization chart of your current company.

画出您目前任职公司的组织管理图，标出您在公司中的位置。

hold tube bend in position, fig. 5, and mark tube on level with top of hex on compression coupling. cut off tube at this mark.

将管子弯头握住在位置上，图5，在压紧联轴节上六角顶部标注管道水平位置。

a surveyor's mark on a permanent object of predetermined position and elevation used as a reference point.

某一永久性物体上预定的位置和高度上的测量标记，用作参考标记。

a quick hough transform is used to detect circular pcb mark based on discussing advantages and disadvantages of several hough transforms. after position calibration the range of solder joint location is confirmed.

本文通过讨论几种定位圆识别方法的优缺点，选择采用快速Hough变换的方法进行定位圆识别来完成电路板位置校准，并在位置校准的基础上进行焊点位置范围的固定。

Please mark which position you are looking for, expected salary and contact way.

请一定注明申请职位 、 薪酬要求和联系方式.

Mark around the block outline, pivoting the neck dart and waist dart into the new position.

标出样板轮廓线,把领省和腰省旋转到新的位置.

Site mark the required position, e . g . 10 cm below the underarm point at B.

定出所需位置并标记号, 如B处,腋下10cm处.