normal stress的例句大全

The circumferential normal stress is tensile.

周向正应力是张性的.

Interfacial stress and normal stress of adhesive increase with the increase of shorting length of CFS-GFS.

随着纤维布有效粘贴长度的减小,胶层端部界面剪应力与正应力成比例增加,增加比例随距离的增加,呈递减趋势.

The result shows that there is no obvious evidence that the variations of the normal stress and Coulomb's failure stress caused by main shock are good for occurrence of aftershocks.

结果表明，主震产生的正应力变化和库仑破裂应力变化并没有明显的证据有利于余震的发生。

However, at higher angle of tooth-shaped asperities and under higher normal stress, the failure model II is found, which is in first tension but final shear failure.

在较高的法向应力下，含起伏角较高齿形节理面的非贯通节理岩体可能出现破坏模式II（先张拉后剪切破坏模式）。

The stress distribution is studied under different serosity pressure. ( 7) The normal stresss and shear stresss at any section are studied.

研究了不同注浆压力对土体应力分稚的影响：（7）研究了注浆过程中土体中任一截面处正应力与剪应力的对比关系。

An approximate analysis of net section normal stress in a laminate strip with a circular hole

含孔层压板条净截面正应力的近似分析

According to small deflection theory and principle of superposition, the normal stress due to bending and axial force may be treated separately.

单索面斜拉桥承受弯矩与轴力的共同作用，根据小变形理论与叠加原理。

The volcanic eruptions are correlated with geoid, the positive geoid anomaly can build up high normal stress, which is in favor of huge eruptions.

火山喷发活动还与当地的重力势有关，重力势正异常可能与高的正压力有关，有利于产生特大喷发。

Thus the directions that emerge for extremizing the normal stress are the directions corresponding to the principal stresses.

因此，产生最大正应力的方向就是相应于主应力的方向。

The normal stress is the control stress which causes cracks in the basement wall;

沿墙长方向的正应力是导致墙体开裂的控制应力，墙中应力较大，墙端应力较小；

Discussion on the Change of Normal Stress on Fault plane and Its Influence Factors ── Part 1 Forming Conditions of Complicated Fault-Block Oil Fields

论断层面正应力变化及影响因素&复杂断块油气田形成条件系列论文之一

Considering the non-linear elastic behaviour of concrete, the normal stress at fibre ends and thermal effect on shear stress and normal stress in fibre, the traditional shear-lag theory of stress transfer in short fibre reinforced concrete-matrix composites is improved.

根据混凝土的非线弹性性质、纤维端部应力和由于温度变化产生的温度应力对剪应力及纤维正应力的影响，对短纤维增强混凝土应力传递的剪滞理论进行改进。

The deformations in the contact slice of the model consist of two parts i.e. shear deformation and sliding deformation. For the normal constructive model, the nonlinear model between the normal stress and normal relative deformation was adopted.

该模型将接触带内的变形分为剪切变形与错动变形两部分，对于法线方向采用法向应力与法向相对变形之间的非线性模型。

The a stop-fracture effects depend on the depth of the saw kerf and average normal stress which exert on the saw cut representing the main fault.

这种止裂或滞后作用依赖于锯口的深度l和施于主断面上的正应力x。

The two types of steel bar stress growths is not synchronous, the normal stress of reinforcement grows much faster. The calculation formula of two types of steel bar in beams was deducted by reinforcement stress analysis.

然后，分析了两类钢筋的应力增长情况，非预应力钢筋的应力增长相较预应力钢筋要快一些，并提出了钢筋应力的计算公式。

It is to use finite element method to calculate the stress within the slope in this paper, and get the normal stress and tangent stress of the slope sliding surface directly, and then calculate the stability coefficient of the slope.

本文研究内容是应用有限元法计算斜坡内部的应力，并直接求解边坡滑动面上的法向力和切向力，进一步计算边坡的稳定系数。

Fault sealing is closely related to the function of stress. Therefore, we can study fault sealing through calculating the size of normal stress of fault plane, on the basis of considering overburden load and regional major compressive stress.

断层封闭性能与应力作用密切相关，可以在考虑断面受到区域构造应力与断面上覆地层负荷联合作用的基础上，通过计算断面所承受的正应力来研究断层封闭性。

After wheel re-pro filing, the wheel wear rate increases which will reduce the wheel turning period. The normal contact stress tends to be stable after wheel wear and is not obvious related to the wear volume around the nominal rolling circle.

车轮经过镟修后，磨耗速率会增加，镟修周期缩短，车轮经过磨耗后法向接触应力趋于稳定，车轮滚动圆磨耗量与法向接触应力无明显关系。

According to this optimization design, the distribution and values of normal contact force and Mises stress for different tooth profiles are obtained. The comparison among the analysis results are carried out, which provides a new study method for the structure optimization of transmission gears.

根据该优化方案，得到了各种型面下的接触法向力和Mises应力的分布情况及大小，并对所得结果进行比较，为传动齿轮的结构优化提供一种研究方法。

Degenerative change and the reaction of stress of intervertebral disc can also change the "normal" cervical lordosis.

颈椎间盘的退行性变和对压力的反应，同样可以改变〃正常〃的颈椎前凸曲度。