pressure molding的例句大全

material is cement, sand, coal dust, high pressure molding , need not sinter. the product with good strength , colourful.

原料由水泥、黄砂、粉煤灰组成，高压成型无需烧结，成品瓦强度高、色彩丰富。

technical transformation of pneumatic micro-jolt high pressure molding machine

对自制双工位气动微震高压造型机的技术改造

transformation of knock-out system of automatic high pressure molding line

高压造型自动线落砂系统的改造

study on preparation of sialon bonded sic by pressure molding

干压成型法制备SiC-Sialon复相材料的研究

Experimental study on casting technology of compacted graphite iron powerful diesel engine cylinder block was carried out on existing cylinder block high pressure molding line. The composition of base iron was 3.6%~ 3.9% C;

在现有汽缸体高压造型生产线上进行大马力柴油机蠕墨铸铁缸体的试验，试验铁液化学成分w为3.6%~3.9%C；

Advanced cast methods used domestically and abroad in famous automobile manufacturers and foundries for cylinder castings of which technical performance has been presented include air impact molding, static pressure molding, vertical parting flaskless molding machine and full mold casting, etc.

介绍了汽缸体铸件的技术性能、国内外各大汽车公司和汽车铸造厂所采用的先进铸造方法，这些方法有气冲造型、静压造型、垂直分型无箱射压造型、实型铸造等。

The results showed that the thickening effect of combined thickeners which were well suitable for viscosity conditions of low pressure molding and low cost conditions of industrialized production, was better than single thickener.

研究表明，联合增稠剂的增稠效果比单一增稠剂的增稠效果要好，更加符合低压模塑的粘度和工业化生产的低成本要求。

Fiber Dispersion& Molding Viscosity Control of Low Pressure Molding Compounds

低压片状模塑料纤维分布与模内粘度控制

industry: pressure gauge; stamping die; molding; sheet metal processing; license plate frame; hydraulic fittings;

所属行业：压力表；冲压模；成型模；钣金加工；车牌架；液压接头；；

it was found that the compression speed and compression stroke are the two factors affecting the molding pressure most significantly.

由模拟找出了压缩速度与压缩行程是两个影响成型压力极大的因素。

industry: offset; binding machine; molding; pressure processing; welding and bonding; advertising;

所属行业：胶印机；装订机；成型模；压力加工；焊接和粘接；广告策划；；

the article briefly describes the test method and principle for molding sand low green compressive strength test by using of the low pressure cramp device.

简述了使用低压夹具测试型砂低湿压强度的试验方法和原理。

But fiber volume fraction are raised via elevating molding pressure, when the molding pressure are too high the fibers will be damaged seriously, the composites will become brittler and show poor mechanical properties as a result.

但是纤维体积分数的增加要通过提高模压压力来实现，当模压压力过大时，纤维出现机械损伤，复合材料变脆、力学性能降低。

Different body molding pressure, optimal value ceramic binder content is different.

不同的坯体成型压力下，陶瓷粘结剂含量最优值是不同。

The percentage reduction in molding pressure is higher if part becomes thinner when using ICM.

使用射出压缩成型时成品较薄的部分成品压力变化的百分之将提高.

The injection molding process of thermoset plastics bulk molding composition ( BMC) made of automobile lamp reflector is presented in the paper. Process parameters are settled such as barrel temperature, screw speed, injection pressure, injection velocity and holding time and so on.

介绍了热固性团状模塑料（BMC）注射成型汽车前照灯反射镜的工艺过程，确定了BMC注射成型的料筒温度、螺杆转速、注射压力、注射速度和保压时间等工艺参数。

By using mushy extrusion molding for magnesium alloy, the disadvantage of pressure casting is avoided.

采用糊态挤压成型镁合金避免了压力铸造的缺点。

Diameter Equalize Molding of Heat Pressure Tee

直径补偿热挤压三通的成型

To show time pressure control curve of high pressure gas, and to discuss the formation and resolving method of detained score defect in the technique of gas assisted injection molding.

给出了气体辅助成型工艺中高压气体注入的时间压力控制曲线。最后讨论了气体辅助成型制品中滞留痕缺陷的形成原因和防治方法。

Influence of molding pressure and dunking time on the sulfate attack resistant nature of concrete

成型压力和浸泡时间对混凝土抗硫酸盐侵蚀性能的影响