process conditions的例句大全

The favorable process conditions is obtained , which has advantages of economic raw materials and high benefit.

该方法具有原料便宜易得、经济效益高等优点.

Objective To determine the molding process conditions of the medicinal carbon granules.

目的确定药用炭颗粒剂的成型(制粒)工艺条件.

The evaluation results showed that under optimized process conditions, the ethylene yield of typical paraffinic atmospheric residue through single pass cracking reaches 26% and the total yield of olefins ( C 2~ C 4) exceeds 50%.

评价试验结果表明，典型石蜡基常压渣油在优化的工艺条件下，单程裂解的乙烯质量产率可达26%，C2～C4总烯烃质量产率超过50%。

Study on platinum electrodeposition ⅰ-process conditions and deposit properties

电沉积铂研究Ⅰ-工艺条件与镀层性能

Optimization of ISSR-PCR System for Lucuma nervosa by Using Orthogonal Design Through the study on the added amount of NaOH, reaction time and temperature, the optimum production process conditions were determined.

蛋黄果ISSR-PCR反应最佳体系的构建（简报）通过对氢氧化钠的加入量、应时间、应温度等生产条件的研究，得出了最佳生产工艺条件。

An Investigation on Process Conditions of Cotton/ Spandex Weft Stretch fabric

棉氨纶纬弹织物工艺条件探讨

A study on coating process conditions of casing tablets by orthogonal design method

用正交设计法研究肠溶衣片的包衣工艺条件

Now the main method is to optimize the process conditions preferably by the specific experiments to examine the resin purification of each step of the active ingredient. The experiments aim at the specific separation objects, and did through regarded the measured target composition as an indicator.

并且研究思路基本集中在针对具体的分离对象，以测得的目标成分得率或含量为指标，设计具体实验考察树脂纯化各步骤对有效成分的影响，从而优选出最佳的工艺条件。

It is thought that the main reasons of unpopularity are undesirable water-based visbreaking performance and imperfect process conditions.

分析认为：水基降粘剂性能不佳以及工艺条件不完善是造成其推广受阻的主要原因。

Influences of electrolytic parameters ( the ratio of ton to toff, frequency, mean current density and temperature of electrolyte) on synthesis of nano-fibrous PANI were studied in detail. The process conditions were optimized.

详细探讨了电解工艺参数（脉冲占空比、频率、平均电流密度以及溶液温度）等对纳米纤维聚苯胺膜合成的影响，获得了制取纳米纤维聚苯胺的最佳工艺条件。

Studied the influence of the expanded graphite and magnesium hydroxide as flame retardant additives on fire properties of coating 、 the titanium dioxide and talc as inorganic filler on the coating properties, and confirmed the optimum process conditions.

研究了无机阻燃剂膨胀石墨和Mg（OH）2对涂料耐火性能的影响，研究了填料TiO2和滑石粉对防火涂料性能的影响，确定了最佳工艺条件。

【 Results 】 The optimal process conditions for Flos Datura were as follows: soaking the medicinal material for 2 hours with 10 times of 75% alcohol, with continuous radiation for 25 min at the power of 730 W, at 65 ℃.

【结果】洋金花微波提取的最佳工艺条件是用药材10倍量的体积分数为75%乙醇浸泡2.0h，在功率为730W，温度为65℃的微波条件下连续辐射25min。

the process conditions and control points of calendaring technology for pvc film are systematically introduced, and the problems in the production of the film are discussed and solved.

系统地介绍了PVC薄膜的压延生产工艺及控制要点，并对产品所存在的问题进行了探讨解决。

Study on the Process Conditions of Transformation Linoleic Acid into Conjugated Linoleic Acid Via Lactobacillus Acidophilus

嗜酸乳酸杆菌转化亚油酸为共轭亚油酸工艺条件的研究

it was found that ferrous oxide with particle size less than 40 nm could be prepared by controlling a certain process conditions.

结果发现，在一定的试验条件下，可获得粒度小于40nm的氧化铁。

The optimum process conditions are as follows: the ratio of n ( FeCl_2)/ n ( BaCO_3) 1.2, the stirring time 3 h under slight boiling state.

优化工艺条件：氯化亚铁与碳酸钡物质的量的比值为1.2，在微沸状态下搅拌反应3h。

several kind of oxidant and oxidation reinforcer are found and their formulation and optimum process conditions are elementally determined.

找到了几种氧化剂和氧化增强剂，初步确定了它们之间的组合和优化工艺条件。

In the article, the process conditions of wet surface modification of aphanitic graphite are studied.

选用不同的偶联剂对隐晶质石墨粉进行表面化学改性。

The optimum process conditions in surface modification were obtained: the HA calcining temperature: 1000 ℃, the addition of PL coupling agent: 0.7wt%.

其较佳的表面改性工艺条件：HA煅烧温度：1000℃；偶联剂加量：0.7wt%。

Using the fractions of vacuum distillate LDAO with cut temperature more than 500 ℃ by hydro-upgrading at laboratory in SINOPEC Jingmen Branch as feedstock, process conditions of ketone-benzol dewaxing& deoiling were investigated at laboratory.

以中国石化荆门分公司实验室加氢改质轻脱>500℃馏分油为原料，在实验室考察了酮苯脱蜡脱油工艺条件。