quenching的例句大全

Under the full consideration on the interaction of the temperature field, the microstructure field and the internal stress field of a quenching test-piece, the numerical calculation models of the three kinds of fields of a shaft-type test-piece are set up.

在充分考虑淬火试件温度场、显微组织场和内应力场相互作用的情况下，建立了轴类淬火试件三种场量的数值计算模型。

Fluorescence quenching reaction of Tetracaine hydrochloride with Eosin Y and their analytical applications

曙红Y-盐酸丁卡因体系的同步荧光猝灭反应及其分析应用

Optical Fiber Sensor for Tetracycline Based on Fluorescence Quenching of Covalently Immobilized Anthracene

基于含蒽荧光共聚物膜的四环素荧光光纤传感器

The poly ( tetrafluoroethylene) particles untreated with quenching showed poor abrasion performance with 22% wear rate after 10 weeks, despite better scale-preventing and scale-removing performance.

不经淬火处理的聚四氟乙烯颗粒，防垢、除垢效果较好，但耐磨性能差，10周后磨损率达22%；

The luminescence intensity and chromaticity of the Eu3+ reached its highest in case of mixing Gd3+, 21mol%, into Thenardite ( Na2SO4: Eu) crystal lattices, and Concentration quenching effect ultimately occurred.

当Gd3+以21mol%掺入到无水芒硝（Na2SO4：Eu）晶格中时，可以达到Eu3+的最强发光强度和最佳色纯度，最终出现浓度淬灭现象。

The segregation concentration of P at prior austenite grain boundaries has been measured with selective etching and found to be related to quenching temperature fitting McLean's theory of equilibrium segregation.

用饱和苦味酸溶液腐蚀显示奥氏体晶界，通过奥氏体晶界腐蚀沟槽深度估算出杂质磷在奥氏体晶界的平衡偏聚浓度，它和淬火加热温度之间的关系符合Mclean的平衡偏聚理论。

Quenching tempering technological parameter for 590 MPa High strength thick steel plate

590MPa高强度厚钢板的调质工艺参数研究

Research on Technological Principle and Organic Properties of Laser Quenching of Alloy Cast Iron

合金铸铁激光淬火工艺规范与组织性能

The influences of quenching temperature, cooling pattern and temper temperature on the structures and properties of high chromium cast iron roll were investigated.

研究了淬火温度、淬火冷却方式和回火温度对高铬铸铁轧辊组织和性能的影响。

The effects of quenching temperature, cooling pattern, temper temperature and temper times on the structure and properties of high carbon and vanadium high speed steel ( HSS) roll were researched and the optimal heat treatment technical parameters were determined.

研究了淬火温度、冷却方式、回火温度和回火次数对高碳高钒高速钢轧辊组织和性能的影响，确定了最佳热处理工艺参数。

Effects of high Temperature Deformation Quenching on Grain Refinement of 20 Dual-phase Steel

高温形变热处理对20双相钢晶粒细化的影响

We study the process of rapid quenching of the liquid iron at 2200K through 2000K, 1800K, 1600K to 1400K and then obtain the statistical analysis of the pair distribution function, mean square displacement, correlation and the Voronoi polyhedra at the temperature equilibrium state.

研究了液态铁在2200K下淬火，经过2000K、1800K、1600K至1400K的过程，并统计分析了各温度平衡态的双体分布函数、均方位移、配位数、及对Voronoi多面体进行分析。

The low cycle fatigue property of surface quenching grade C steel is higher than that of normalization grade C steel and quenching and high temperature tempering grade C steel.

表面淬火C级钢比调质C级钢和正火C级钢的低周疲劳性能高，在应变量较大时，调质C级钢和正火C级钢低周疲劳寿命较高；

Surface hardness of bearing steet decreased after quenching, because temperature traverse quickly in cooling-off The case happens easily when the time of steam film is longer and the temperature of quenching oil is lower.

轴承钢油淬后往往发生表面硬度偏低，其原因是因为冷却途中冷速急剧变化引起的，特别是在蒸汽膜期长，特征温度低的油中淬火时更易发生。

Conventional heat treatment of low alloy martensitic wear-resistant steel is quenching and low-temperature tempering process, from which it can get tempered martensite structure which has a good combination of strength and toughness.

低合金马氏体耐磨钢的传统热处理工艺为淬火后低温回火，得到回火马氏体组织，具有良好的强度、硬度和韧性的配合。

The results show that matrix is mainly tempered martensite under the condition of quenching at low temperature and tempering at 550 ℃; retained austenite content increases and martensite content relatively decreases along with the increase of quenching temperature, meanwhile, the wear resistance improves.

结果表明：550℃回火条件下，低温淬火时基体组织以回火马氏体为主，随着淬火温度升高，残余奥氏体含量升高，马氏体含量相对减少，而耐磨性随淬火温度升高逐渐升高；

The tempering curve of remaining thermal quenching is higher than that of two times quenching.

余热淬火的回火曲线高于二次淬火的回火曲线；

The accuracy of temperature in quenching and tempering furnace was controlled within ± 5 ℃.

淬火炉和回火炉控温精度均

Quenching Hardness Calculation and Tempering Hardness Characteristic of Cr-W-Mo-V Medium-alloy Steel

Cr-W-Mo-V中合金钢的淬火硬度计算及其回火硬度特性

The changes of quenching and tempering hardness and the microstructure transformation of four kinds of Cr-W-Mo-V medium-alloy steels were investigated.

研究了4种不同成分的Cr-W-Mo-V中合金钢的淬火硬度、回火硬度变化和组织结构转变。