resistance electrode的例句大全

The model contains ohm resistance, a constant phase angle element ( CPE) standing for double electrical layer on porous electrode, charge transfer resistance and Warburg resistance.

模型包含欧姆阻抗、多孔电极双电层的恒相位元、电荷传递阻抗和Warburg阻抗。

Error Analysis of Ground Resistance Measurement by Three Electrode Angle Method

三极夹角法测量接地阻抗的误差分析研究

The Study of Deposition of TiC on the Electrode Tip Surface of Resistance Spot Welding by Vibrating Electric Sparking

点焊电极表面振动电火花熔敷TiC的研究

The effect of TiC coating in electrode tip surface on spheriform electrode degradation during resistance spot welding zinc coated steel was investigated by SEM, EDX and XRD.

利用SEM、EDX和XRD等方法分析了在点焊镀锌钢板时球形电极表面熔敷TiC涂层对电极失效的影响。

The results show that electrode degradation mechanism was basically caused by wear due to fracture of local welding between the electrode tip surface and zinc coated sheet steel happen at electrode surface and alloying between electrode and zinc on zinc coated steel during resistance spot welding zinc coated steel.

结果表明：点焊镀锌钢板时电极的失效机制主要是电极和镀锌板之间局部焊接的断裂发生在电极表面而导致的电极磨损以及电极和镀锌板表面的锌之间的合金化。

The electrochemical reaction resistance can be decreased adopting wet method, the reactive resistance of hydride electrode are 0.30 Ω, 0.24 Ω and 0.15 Ω respectively corresponding to dry method, wet method and wet method with additive.

降低电极电化学反应电阻，采用干法、湿法或湿法加添加剂制粉工艺贮氢电极的反应电阻分别为030Ω、024Ω和015Ω；

Electrode life and surface characteristics in resistance spot welding of aluminum

铝合金电阻点焊电极寿命及其表面特征分析

This study shows that alloying elements can increase the electrode potential shift of the surface Ni atoms, increasing the electrochemical stability of the surface, improving the corrosion resistance without passive film and preventing corrosion wear.

此研究表明合金元素的合理选择能有效提高合金表面Ni原子的电极势，增强表面电化学稳定性，提高无钝化表面的抗蚀性，防止腐蚀磨损。

Combining with effective TPB resistivity and ionic resistivity, electrode polarization resistance can be estimated.

结合TPB和氧离子有效电阻率可以进一步计算极化阻抗。

Study on Increasing the Yield Strength of Autobody Resistance Welding Electrode

提高汽车车身电阻焊电极屈服强度的研究

Research status and development of the electrode materials in resistance welding of galvanized steel sheets

镀锌钢板电阻焊电极材料的研究现状及进展

the relations between the resistance of the plasma channel of pulsed discharge in water and the circuit parameters are discussed; the laws of the channel resistance changed with capacitance, initial voltage and electrode gap width are presented.

对水中脉冲放电等离子体通道电阻与放电参数之间的关系作了研究，得到了等离子体通道电阻与电容量、初始电压、电极间距离的关系，以及通道电阻随时间的变化规律。

This observation led to the presumption of a struc-tural model of the electrode and explained the beneficial effects of the intermediate layer on depressing the interfacial resistance of the electrode and improving the adhesive power between both β-PbO_2/ SnO_2 and Ti/ SnO_2.

因而提出了电极结构模型的假设，并且解释了中间层对降低界面电阻，改进β&PbO2/SnO2与Ti/SnO2之间结合强度的有益作用。

Traditional Ni/ MH battery pack is composed of series connected cells. There are connection parts such as electrode tab, connection bar, battery case, etc., these increase the weight and intrinsic resistance of the battery.

传统的MH/Ni电池组是由单体电池串联而成，在电池组中存在极耳、连接条、电池壳等连接体，增大了电池的质量和内阻。

If there is a large contact resistance between the electrode and the semiconductor film, the performance of devices would be significantly decreased due to heat or poor contact. Therefore, ohmic contact with low resistance and thermal stability is very critical.

如果接触电极和半导体之间存在较大的接触电阻，那么器件的性能就会由于散热或者接触不良而显著下降，因此获得低电阻、热稳定的欧姆接触非常关键。

The last semicircle or line in the low-frequency region was for the resistance of the interphase between the counter electrode of Li and electrolyte solution or the diffusion of lithium-ion in the CAW electrode.

而处于低频端的直线或半圆对应于锂离子在碳原子线电极中的扩散或对电极锂片与电解质之间的界面阻抗。

Electrochemical impedance spectra ( EIS) measurements revealed that with the DOL pretreatment lithium electrode had lower and more stable interface resistance during the storage in electrolyte for a long time.

电化学阻抗谱（EIS）分析表明，当金属锂电极长时间浸泡在电解液中时，经过DOL预处理的锂电极与未经处理的锂电极相比，具有更低、更稳定界面阻抗。

Plate electrode of ZC 36 type high resistance meter is put into thermo tank. The insulation resistance of dust is measured with high resistance low voltage, and then the specific resistance is calculated.

应用ZC-36型高阻计测量箱中的圆盘电极改装入恒温箱中，采用高阻计低压法测量出粉尘的绝缘电阻R，再经计算得出粉尘的比电阻ρ。

resistance spot welding. electrode holders. part 1 : tapper fixing 1:

电阻点焊.电极夹.第1部分：固定锥度为1：

electric resistance welding. spot welding electrode adaptor with punching cooling bore. sizes and tolerances.

电阻。带冷却孔的点电极转接套。尺寸和公差。