rolling process的例句大全

Continuous Casting-Direct Rolling Process in Shenyang SteelWorks

沈阳钢厂连铸－直接轧制

3-D Coupled Thermo-mechanical Analysis of the Tube Round during Two-Roll Rotary Rolling Process

实心坯二辊斜轧过程三维热-力耦合分析

Analytical Study on Lubrication States and Velocity in Aluminum Foil Rolling Process

铝箔轧制润滑机理和速度效应的研究

Research on Burnish Machine in Compound Material Cold Rolling Process

钢基复合材料生产中打磨机理研究

The main program and subroutines are programmed in C language. Thermo-mechanical Coupled Analysis of Continuous Cast Rolling Process Using MARC Subroutines

测试单元所用主程序及子程序均采用C语言编制。基于MARC二次开发的连续铸轧热力耦合分析

Temperature field finite element during flat hot continuous rolling process with compact double stand reversing rolling mill was researched, which is the only one in China.

实现了对国内唯一一架双机架紧凑式可逆炉卷轧机板材热连轧的温度场有限元研究。

A rigid pushing model based-on 3D thermo-mechanical coupled analysis with FEM was used to simulate wire and rod multi-pass continuous rolling process.

基于三维热-机耦合有限元分析方法建立了刚性体推动模型，模拟棒线材多道次连轧过程。

The impact test to angle iron at different temperatures showed that the impact energy reduced with the temperature decreased and the rolling process affected the low-temperature toughness greatly in addition to the composition of alloying elements.

在不同温度下的角钢冲击实验结果表明，随着温度的降低，冲击功逐渐降低。除了合金元素的成分对低温韧性的影响外，轧制工艺对低温韧性的影响也很大。

Test results of lead work-pieces verify the feasibility of rolling process and die design.

铅试件辗压试验结果证明辗压成形工艺和模具设计的可行性；

Brief Introduction of Continuous Rolling Process and Pass System in Continuous Rolling Bar Plant

连轧棒材厂连轧工艺及孔型系统简介

This paper discusses the effect of rolling process and pass design on product quality for the flat spring steel with single-side and two-slot.

本文阐述了单面双槽弹簧扁钢的轧制工艺及孔型设计对产品质量的影响。

To unite with manufacture practice, the optimization method of the dynamic programming law in the groove design of bar and wire stock was investigated. A set of computer software aiming at minimum energy consumption was offered for high-speed rolling process of the bar and wire stock.

结合生产实际，研究了动态规划法在棒、线材孔型设计中的优化方法，为高速线、棒材生产提供了一套以低能耗为目标的计算机优化软件。

Numerical simulation of new ring rolling process of tubeless steel wheel

无内胎钢制车轮辗环成形新工艺及其数值模拟

Development of the Mass Flow Simulation System of Thin Slab Continuous Cas-ting and Rolling Process

薄板坯连铸连轧流程物流仿真系统的开发

Thickness control for rolling process by sensitivity based on support vector machine

基于支持向量机灵敏度的轧制过程厚度控制

Hybrid Intelligent Modeling Approach for Dynamic Cold Tandem Rolling Process

冷连轧动态过程混合智能建模方法

Research on Temperature and Strain Fields Distribution of Hot Ring Rolling Process

环件热辗扩温度场和应变场分布的研究

Computer software for simulating vertical section of deformation zone on Accu Roll rolling process developed on the basis of models built, which puts the base for optimizing process parameters.

在建立Accu-Roll轧机变形区模型的基础上，开发出计算机模拟软件，可方便地通过变形区纵剖面计算机图象显示分析工艺参数对变形区的影响，从而为合理地选取与优化工艺参数提供依据。

multi-pass deformation also shows that in high-temperature rolling process, the material will be softened as a result of the recovery and recrystallization, so the rolling force is reduced and the time interval of the passes of rough rolling should be longer.

多道次变形还表明，在高温轧制过程中，道次间隔的时间内，材料会发生回复和再结晶而软化，降低了轧制力，因此粗轧各道次间隔时间长一些。

The finite element model of wheels sliding on the rails and rolling process are established by large-scale finite element software ANSYS. Establish contact using the contact element method in the wheel-rail contact area.

主要应用大型有限元软件ANSYS分别建立车轮在钢轨上滑动和滚动过程的有限元模型，在轮轨接触区利用接触单元法来建立接触。