rolling process的例句大全

Study on Rolling Process of the Thick Wall Seamless Tube

厚壁无缝管轧制工艺研究

Thickness control for rolling process by sensitivity based on support vector machine

基于支持向量机灵敏度的轧制过程厚度控制

Research and practice of Steel 20 produced by thin slab casting and rolling process

薄板坯连铸连轧流程生产20号钢的开发与实践

These models were necessary to investigate different thin strip rolling process.

这些模型全面描述了不同状态的板带轧制过程。

The Study of 72 Mn Bimetal Thin Strip Rolling Process

72Mn双金属薄带轧制工艺的研究

The steady heat balance state of the tire in the rolling process was researched.

研究轮胎滚动过程中的稳态热平衡状态。

Cold Rolling Process and Major Equipment for Producing Titanium and Nickel Plates

钛、镍特种金属板带冷轧生产工艺及设备选择

Research on the Hot Continuous Rolling Process for High Speed Titanium Wire Rod in Heavy Coils

大卷重纯钛高速线材热连轧工艺研究

In view of the trial-production of J55 hot-rolled coiled sheet for petroleum casing pipe, rolling process control and comprehensive quality of the products were analyzed.

针对J55石油套管热轧板卷的试制情况，重点从轧制过程控制、产品实物质量进行了分析。

Influence of Rolling Process on Microstructure and Mechanical Property in Microalloy V-N Steel

轧制工艺对微合金V-N钢显微组织和性能的影响

Inverse determination of thermal boundary condition parameters in hot rolling process by numerical analytic method

应用解析数值法反求热轧过程的传热边界条件

The introduction covers a briefing about the development of the three-roll pipe mill abroad, the latest situation regarding this kind of mill in the world as well as the pipe rolling process with the mill.

介绍了国外三辊轧管机发展简况、目前世界上三辊轧管机的基本情况和三辊轧管工艺的特点。

The microstructure and properties of the pure copper tube during the rolling process of a three-roll planetary mill were studied using optical microscope, Brinell's hardness measurements and laser-thermal rating measurements.

采用金相显微镜、布氏硬度仪以及激光热导仪对三辊行星轧制过程中紫铜管的组织和性能进行研究。

3-D Coupled Thermo-mechanical Analysis of the Tube Round during Two-Roll Rotary Rolling Process

实心坯二辊斜轧过程三维热-力耦合分析

Thermo-mechanical Coupling Analysis of Continuous Cast Rolling Process Using MARC Software

基于MARC平台的连续铸轧热力耦合分析

The main program and subroutines are programmed in C language. Thermo-mechanical Coupled Analysis of Continuous Cast Rolling Process Using MARC Subroutines

测试单元所用主程序及子程序均采用C语言编制。基于MARC二次开发的连续铸轧热力耦合分析

A rigid pushing model based-on 3D thermo-mechanical coupled analysis with FEM was used to simulate wire and rod multi-pass continuous rolling process.

基于三维热-机耦合有限元分析方法建立了刚性体推动模型，模拟棒线材多道次连轧过程。

To unite with manufacture practice, the optimization method of the dynamic programming law in the groove design of bar and wire stock was investigated. A set of computer software aiming at minimum energy consumption was offered for high-speed rolling process of the bar and wire stock.

结合生产实际，研究了动态规划法在棒、线材孔型设计中的优化方法，为高速线、棒材生产提供了一套以低能耗为目标的计算机优化软件。

Development of the Mass Flow Simulation System of Thin Slab Continuous Cas-ting and Rolling Process

薄板坯连铸连轧流程物流仿真系统的开发

Using controlled rolling and controlled cooling process and changes of various process parameters improve the structure of plate, enhance strength, toughness and hardness of the plate so as to reach the target of comprehensive properties of the plate.

通过控制轧制控制冷却工艺，改变各项工艺参数，来改善钢板的组织结构，提高钢板的强韧性和硬度，从而达到提高钢板综合性能的目的。