shear angle的例句大全

Through the checking calculation and adjusting of the parameter of the shear wall using the deformation aim gained from the inelastic displacement spectra method and the fitted drift angle evaluation function of deferent performance level, the performance level of the shear wall could he realized.

根据弹塑性位移反应谱法得到的目标位移和本文拟合的剪力墙构件各性能状态位移角估算公式进行验算、调整，可以实现剪力墙结构不同的性态目标。

The diffusion of rotation is concerned with shear velocity. The particles have large angle and optimal orientation in the region with large curve flow stream.

纤维粒子旋转扩散与流场的剪切速度有关，在流线曲率大的区域，纤维与流线的夹角较大，并有最优取向：而在纤维与流向一致的区域内流线比较平直。

The transverse weld topography, the connect width between plates and tension and shear load were analyzed when the incident angle changed.

分析了入射角改变对焊接件外观形貌、焊缝截面、焊缝板间连接宽度以及所承受的拉剪载荷的影响。

For general reinforced concrete foundation, there is larger horizontal shear stress when the incident angle of P_1 wave is between 30 ° and 50 °;

对于通常的钢筋混凝土建筑，当P1波入射角为30°~50°时，基础容易产生较大的水平剪应力；

The shear of woven fabrics results largely in the alteration in the angle between warp and weft yarn.

机织物的剪切作用，大部分由经纱和纬纱之间角度的改变所形成。

The analysis of seismic responses of shear-wall structures with angle windows

开设转角窗剪力墙结构的地震反应分析

The influence of the bearing structure, eccentricity, spiral angle, rotating speed and critical shear stress on slip degree is studied.

研究了轴承的结构、偏心率、螺旋角、转速和极限剪应力对滑移程度的影响。

After optimization, the cutting angle and The difference between the instantaneous velocity and the average velocity in the cutting area of the shear are decreased.

优化后，在剪切区，剪刃剪切倾角和连杆水平速度均匀性两项指标均有所提高。

design on ferroconcrete shear wall of high-rise building in 8 angle area

8度区高层建筑钢筋混凝土剪力墙的设计

design of parallel beam splitter whose shear difference is insensitive to incident angle

剪切差对入射角不敏感的平行分束偏光镜的设计

firstly, influence of core parameters ( pin diameter, insertion angle, density, oblique angle, insertion depth and its layout) on tension, shear and compression response is investigated experimentally.

首先，采用试验方法研究了pin直径、植入角、植入密度、端部斜切角、植入深度以及pin空间布局等参数对X-cor泡沫夹层结构拉伸、压缩和剪切性能的影响。

among all parameters, pin insertion angle, pin diameter and pin density are primary for compression and shear properties, while the oblique angle and pin layout could be neglected except that pins on transverse plane about shearing load have little contribution to the shear behavior.

Pin植入角、直径以及植入密度是压缩和剪切性能的主要影响因素，而端部斜切角及空间布局的影响可忽略。此外，横向面内pin对剪切性能的贡献较小。

a new exploration of the shear plane angle's theory with fem

剪切角理论研究有限元新方法探索

However, at higher angle of tooth-shaped asperities and under higher normal stress, the failure model II is found, which is in first tension but final shear failure.

在较高的法向应力下，含起伏角较高齿形节理面的非贯通节理岩体可能出现破坏模式II（先张拉后剪切破坏模式）。

The effect of transverse shear deformation is considered and angle of rotation of surface normal for each layer is different.

这类板的横向剪切变形效应必须予以考虑，因而层板不同层的表面法线的转角是不同的。

An analysis of size effect of the inclination angle of shear band and the onset, skip and stability of shear strain localization

剪切带倾角尺度律与局部化启动跳跃稳定研究

And the formula for angle of shear plane is modified by chip shortening coefficient.

并通过切屑变形系数来修正模型中的剪切角计算公式。

Larger loading rate leads to larger inclination angle of shear band in the middle of specimen.

随着加载速率的增加，岩石中部剪切带的倾角有增大的趋势。

Bigger inclination angle of shear band leads to bigger dissipated energy of lateral plastic deformation and smaller dissipated energy of lateral plastic deformation.

增加剪切带倾角，侧向塑性变形消耗的能量占剪切带消耗的能量的比例增加。

By integrating the function, the shear force, bending moment and the angle of rotation of the whole beam are expressed by one equation respectively.

通过积分，全梁的剪力、弯矩、转角和挠度可分别用一个方程表示。