shear angle的例句大全

Microcomputer Control System for Angle Bar Punch-Shear Machine

角钢联合冲剪机微机控制系统

Dissipated energy due to axial plastic deformation is proportional to that of lateral plastic deformation and the proportional coefficient is dependent on inclination angle of shear band.

轴向塑性变形消耗的能量与侧向塑性变形消耗的能量成正比，其比例系数与剪切带倾角有关；

Based on the limit equilibrium theory and the hypothesis of planar sliding surface, a formula for calculating the angle of shear failure was deduced considering cohesion and cut slope angle.

基于极限平衡理论及平面滑裂面假定，在考虑土黏聚力及放坡角度的基础上，推导了平面滑裂面剪切破坏角的数学表达式。

Results show that degree of compaction, compaction water content and saturation state of compacted soil have influence on cohesion and angle of friction of clay, thereby on the shear strength of clay.

试验表明，压实度、压实含水量及土体饱和状态对粘聚力和内摩擦角有影响，从而使抗剪强度也受到三因素的影响。

The shear stress concentrates in the retaining substructure and the angle of slope, especially serious in the angle of slope.

剪应力在支护结构和坡角处有集中现象，在坡角处较为严重。

To cope with the demand for a control system dictated by angle bar shearing shop practice, a new dc on-off control system governing the operation of the flying shear in a logic manner is developed.

作者根据起停式角钢飞剪的剪切工艺要求，研制出一种新型的起停式飞剪的直流控制系统。

Statistics Analysis on Friction Angle of Shear Strength for Clay

粘土抗剪强度内摩擦角统计分析

The results of the tests show that with compaction water content increasing, the compression deformation increases, the shear strength decreases and angle of friction also decreases.

试验表明：随压实含水量增大，粘土的压缩变形增加、抗剪强度降低；

Larger inclination angle of shear band is caused by larger rigidity of platen.

压头刚性越大，剪切带倾角增加，试件脆性增强。

The increase of the inclination angle of shear band and its width has an opposite influence on stress-strain curve of specimen after localization occurs.

剪切带倾角和宽度的增加对岩样的塑性性质影响正相反。

The velocity distributing, variation of extension rate, shear rate and the natural convergence angle of the fluid were analyzed under different initial entry pressure.

分析了在不同口模压力（P）下入口区速度分布、延伸应变速率、剪切应变速率以及流体自然收敛角的变化。

For inner shear ( II) type crack, created-fracture angle is-70.5 ° according to maximum tension theory, but the angle has nothing to do with material nature.

按照最大拉应力理论，内剪切型裂缝的开裂角与材料性质无关（-70.5°）；

The deformation parameter and the orientation angle were typically introduced to describe the distorted drop in a shear or an extensional flow.

论述了剪切或拉伸流场中描述液滴形变的两个典型变量即变形度和取向角；

The relationship of the strength of the SiCw/ Al composite and off-axis angle of the SiC whisker is studied with the analysis method of the simplified stress. Investigation on Off-axis Tensile Test for Determination of Shear Characterization of Composites

用简化应力的分析方法推导了SiCw Al复合材料的强度与SiC晶须偏轴角α的关系，并通过试验进行验证.偏轴拉伸测定复合材料剪切特性的研究

The conditions that the most story drift angle of interruptable shear wall height are established.

设定了最大层间位移角θmax为可中断剪力墙的条件。

Slide-resistant pile program has realized these fuctions which are given slip surface count internal friction angle, given the shape of sliding surface design calculation, given the landslide thrust design calculation of landslide, given sliding surface moment, shear force design calculation. 5.

抗滑桩程序设计，实现了对给定滑动面形状反算内摩擦角、给定滑动面形状进行设计计算、给定滑坡推力进行设计计算以及给定滑动面处弯矩、剪力进行设计计算的功能。