shear force的例句大全

Non optical methods of sample tip distance regulation based on shear force which include emission detection with PMT, quartz tuning fork, capacitance, piezoeffect, impedance are reviewed in this paper.

本文综述了扫描近场光学显微镜发展以来所出现的基于剪切力原理进行样品／探针间距的探测的一些主要的非光学方法。

A nonoptical shear force method for tip sample distance regulation

一种探针-样品距离的切变力控制新方法

The high tensile stress parallel to the interface exists at the whisker/ reaction layer interface and in TiC near the interface, at which failure occurs easily when shear force is applied.

SiC晶须/反应层界面及其附近的反应产物TiC内具有较高的平行于界面的拉应力，当连接界面承受剪力作用时，SiC晶须/反应层界面和TiC处极易破坏。

Tectonic force source and seismic source stress field investigation on the coating's static shear stress and surface tension

构造力源和震源应力场涂料静切力及表面张力的研究

Methods The average dissecting force ( ADF) and interlamellar shear stress of each interspace in the media were measured using a tensile strength tester, and the the final shape-changed strength ratio of each layer was calculated before and after melting the tissue with collagenase and elastase.

方法测定人主动脉中膜各层间单位分离力、剪应力和胶原酶和弹力蛋白酶酶解前后主动脉壁各层的屈服形状改变比能。

Firstly, this paper does theoretical research when tension acts on the bolt tip, and derives the distribution law of the bolt shear stress and axial force, and defines three different bolt stress state.

首先，本文对锚杆端部受拉力时做了理论研究，推导出锚杆剪应力与轴力的分布规律，并定义了锚杆三种不同的受力状态。

Key Points on Tension Rod Installation by Using shear Type Constant Force Tester

用剪式恒力仪安装拉杆须注意的要点

The cutting force and the thermoplastic shear instability can directly influence on machining precision, tool life and surface roughness.

在加工中切削力的变化和热塑剪切失稳的发生将直接影响加工精度、刀具磨损和表面质量。

The limit loading formulae of thick-walled tube with differential strength in tension and compression are derived in the twin shear unified strength theory under the combined actions of both an inner pressure and axial force.

应用双剪统一强度理论，考虑材料的拉压异性和同性，推导了在内压和轴力联合作用下的厚壁圆筒的塑性极限载荷表达式。

The expressions of hydrostatic force and viscous dissipative force were employed to clarify the relationship between the hole disappearance phenomen and shear thickening effect.

提出了基于流体动力学的简化模型，利用静水压力和粘性耗散力的表达式阐明了初始扰动的消失和剪切增稠效应的关系。

Combining with three nodes isoparametric axial force element, the new element can be used to accurately calculate the shear flow action between bar and skin in thin-wall structure.

它与三节点等参轴力杆单元组合时可以精确地模拟薄壁结构中杆与蒙皮之间的剪流作用。

influence of process parameters on spinning force and wall thickness difference of shear spinning

工艺参数对剪切旋压旋压力和壁厚差的影响

Based on tests results, the composing of shear bond force, failure mode and the factors of effect on the shear bond strength are analyzed.

根据试验结果，探讨了钢管混凝土界面抗剪粘结力的组成、抗剪粘结破坏特点以及钢管混凝土界面抗剪粘结强度的主要影响因素。

As the rock more softly elastic modulus is smaller, the maximum shear stress and axial force are smaller; conversely, the harder Rock, the greater the elastic modulus, The shear stress and axial force are greater.

岩土越松软弹性，模量越小，受到的最大剪应力就越小；反之，岩土越坚硬，弹性模量越大，受到的剪应力则越大。

Therefore it is very necessary to consider shear deformation and rigid zone in the box culvert endogenic force computation.

因此在箱涵内力计算中考虑剪切变形和刚性域是非常有必要的。

radial lorentz force mainly generates shear wave propagating along depth, while vertical lorentz force mainly generates longitudinal wave propagating along depth.

水平径向洛伦兹力主要产生沿深度方向传播的横波，垂直方向洛伦兹力主要产生沿深度方向传播的纵波。

Analysis of photoelectric hybridization measurement on shearing force for flat shear

平板剪切机剪切力的光电测定分析法

Determination of the shear plane quantity of shearing force bolt connection

剪力螺栓连接剪切面数目的确定

Comparing with the traditional method of drawing internal force chart, this method is very simple, it is easy to master and easy to check-up. It unifies drawing shear diagram and bending moment chart using the differential coefficient connection between load collection degree and internal force.

与传统绘制内力图的方法相比，该方法不仅简捷、直观、易于掌握、便于验算，而且和教材中利用载荷集度与内力之间的微分关系画剪力图、弯矩图，形成有机的统一。

EVALUATION OF ELASTIC AND ULTIMATE FLEXURAL STRENGTH IN DESIGN OF PARTIALLY COMPOSITE BEAM Determination of the shear plane quantity of shearing force bolt connection

部分剪切连接组合梁弹性刚度和极限强度的计算剪力螺栓连接剪切面数目的确定