shear force的例句大全

also have automatic shear folding machine, zigzag sewing machine, etc. , well-equipped, strong technical force.

还备有全自动剪折机、锁边机等，设备齐全，技术力量雄厚。

Reasonable design of shear connector need availably control of horizontal shearing force between steel webs.

合理地设计抗剪连接件需要有效地控制钢腹板和混凝土材料之间的水平剪切力.

The distribution of storey shearing force in frame-shear wall structure is discussed.

讨论了框剪结构在弹性和弹塑性工作状态下楼层剪力的分配机理.

Firstly, the shear strength parameters of slip surface are back-analysised, then quantitive evaluation of landslide is carried out, and the residual sliding force under different conditions are calculated, and abnormal operation mode two is selected as control condition. 3.

首先对滑动面的抗剪强度参数进行反算，然后对滑坡体进行了稳定性定量评价，计算了不同工况下滑坡的剩余下滑力，并选取非正常工况Ⅱ作为抗滑支挡工程设计的控制工况。

A 3D mechanical cutting force model was developed based on the shear and slip-line field method.

基于剪切-滑移线场理论建立微细铣削三维切削力模型。

A 3D mechanical cutting force model is proposed based on the shear and slip-line field method, in which the tool edge radius and elastic restitution in the ploughing field are taken into consideration.

本文基于剪切-滑移线场理论建立了二维振动辅助微铣削的三维切削力模型，模型中考虑了切削刃钝圆半径及耕犁和弹性恢复对微细切削力的影响。

Nonlinear Finite Element Analysis and Study on Restoring Force Models of Slitty RC Shear Walls

带竖缝剪力墙板的非线性有限元分析及恢复力模型研究

A series of factor such as the difference about the centre of figure and the shear centre, curvature radius, central angle is discussed. Sometimes it is better to locate the force half-way between the centroid and the shear centre.

对曲线梁中的剪、形心位置的差异以及曲率半径、圆心角、预应力大小、摩阻损失等内力影响因素进行了分析。有时，荷载作用在形心与剪心距离的一半处较为有利。

The thickness of slab is determined by punching shear capacity. Punching Shear of Concrete Slabs With Shear Rein force ment

其厚度一般是由冲切条件控制的。配抗剪钢筋混凝土板的冲切

based on the axial force equilibrium condition, the appropriate shear lag warping displacement mode is chosen. as for the representative single-box-single-cell trapezoidal girder, the general formulas of the geometrical properties on shear-lag-warping cross section are derived according to the chosen displacement functions.

从剪力滞翘曲应力的自平衡条件出发，选取合理的剪滞翘曲位移模式，给出单箱单室梯形截面箱梁剪力滞翘曲几何特性的一般公式。

Braced frame and steel frame-slits shear wall are commonly used as the resisting lateral force in the earthquake zone.

钢支撑框架以及钢框架带竖缝剪力墙结构是抗震区常用的抗侧力体系。

Coincidence between the orientation of normal contact force anisotropy and the direction of the major principal stress has been observed during all stages of shear loading.

整个加荷过程中，剪切带内大主应力的偏转方向与法向接触力各向异性的主方向保持了良好的一致性。

It produces a considerably large ex-Tensional force in the upper part of the crust and a horizontal shear stress in the middle and lower parts of the crust at the same time.

它能够在地壳上部产生足够大的伸张应力场，同时在地壳中部或下部产生水平切应力场。

Frame computation model discussion of frame-shearing force wall structure under vertical load function

框架&剪力墙结构在竖向荷载作用下框架计算模型的探讨

The tidal force may increase the shear stress on the fault plane and is favorable for earthquake happening if the direction of horizontal tidal force near the fault strike of the earthquake when the earthquake occurs;

地震发生时水平引潮力方位与地震断层面走向接近，可能增加断层面上的剪应力，有利于地震的发生；

The force of instantaneous steady seepage results in the vertical stretching of the foundation under geomembrane and the lateral compression, which make the foundation in the state of pure shear stress with small volumetric compressive deformation, thus, the foundation cannot be reinforced effectively.

瞬时稳定渗流体力使膜下地基竖向拉伸、侧向受压，接近纯剪切应力状态，体积压缩变形较小，难以有效地加固地基。

Contact force generated by particles imposing on the surface of material can form contact shear stress and radial tensile stress.

材料表面受到颗粒冲击产生的接触压力形成接触剪应力，以及在接触边界上产生径向拉应力。

Study on the deformation behaviour and restoring force model of squat shear wall

RC低矮抗震墙的变形性能及恢复力模型研究

Analysis of free vibration for tapered beam including effects of axial force and shear deformation

考虑轴力和剪切变形影响的楔形梁自由振动分析

Vetiveria zizanioides with strong deep roots have better anchoring force and shear resistance.

香根草具有纵深发达的根系系统,具有较高的锚固力和抗剪力.