shear of的例句大全

An eigenmode equation of ion temperature gradient driven instability in a tokamak plasma with negative magnetic shear is solved numerically by the shooting method.

采用打靶法，数值求解了在负磁剪切托卡马克等离子体中离子温度梯度驱动的复本征模方程。

The typical damage features of north asphalt pavement which suffer extreme high temperature climate have been summarized. The rut factor, creep stiffness, dynamic stability and shear parameter of base asphalt, SBS and CMA binders and mixtures were obtained.

总结了极端高温气候下北方地区沥青路面典型破坏特征，获得了基质沥青、SBS、CMA结（混）合料极端高温条件下的车辙因子、蠕变劲度、动稳定度和抗剪参数。

The results show that the welded joint can rotate largely in fire and flexure of column flange and shear deformation are main factors causing the rotation of joint, furthermore, column stiffeners can increase the critical temperature of joint by about 50 ℃.

试验表明：焊接节点在火灾下有较大的转动能力，柱翼缘的弯曲变形和腹板的剪切变形是引起节点转动的主要因素，柱腹板加劲肋可提高节点临界温度50℃左右。

According to the theory the wave number spectrum of the large vortices mainly depends on the atmospheric conditions in both of the upper and lower layers, such as wind speed, wind direction shear, stratification as well as temperature jump.

根据此理论，大涡的波谱构成主要由上、下层大气中风向、风速、层结以及两层之间的温度跃变等因素决定。

Finite Element Analysis of Shear Lag Effect of Box Girder under Temperature Load

温度荷载作用下箱梁剪力滞效应的有限元分析

The effects of foaming temperature, saturation pressure and shear rate on the cell morphology of foamed PLA in microcellular foaming process of supercritical CO2/ PLA were investigated.

研究了超临界CO2/PLA微孔发泡过程中，发泡温度、饱和压力、剪切速率对聚合物PLA泡孔形态的影响。

The influence of shear rate on the viscosity and temperature sensibility was also discussed in details.

研究了含有交联剂发泡料的熔体剪切速率对熔体流动行为以及ηa、温度敏感性的影响。

Analysis on Temperature Stress Caused by Hydration Heat and Crack Control of Shear Walls

墙体的水化热应力分析与裂缝控制

Improving temperature-resistant, salt-resistant and shear-resistant properties is important to the development of PAM-type products with high performances.

耐温、耐盐、抗剪切性能的改善是高性能PAM（聚丙烯酰胺）类产品研究和发展的一个重要方面。

As the adiabatic shear bands form and develop, a series of changes in chip morphology occur which is mainly influenced by the cutting speed and the tempering hardness of workpiece material.

随着绝热剪切带的产生和发展，切屑形态发生了一系列转变，切削速度和工件材料回火硬度是影响这一转变过程的主要因素。

Based on the tendency equation of turbulent kinetic energy, its simplified equation including only wind shear and air stability was derived.

基于湍流动能倾向方程，推导出了其只含风切变和大气稳定度的简化方程。

A study of tensile-shear crack and strength related to jointed rock mass

节理岩体拉剪断裂与强度研究

Analysis of strength and shear-tensile failure of rock specimens with sedimentary weak plane

具有沉积弱面试样的剪切拉伸破坏及强度分析

The correlations between tensile modulus, shear modulus and temperature of PA6 were obtained by linear regression.

利用线性回归，分别得到了拉伸模量，剪切模量与温度的相关关系。

Analysis on the Destruction Procedure of the Tensile Shear Specimen

金属胶接接头拉剪破坏过程分析

The consequence of experiment indicates that the splitting tensile strength of steel fiber concrete increases with the increase of volume fractions, length-diameter ratio, the length and concrete strength grade. The cold drawn steel fiber is superior to the mill steel fibers and shear steel fiber.

研究表明：钢纤维混凝土劈裂抗拉强度随着钢纤维掺量、长径比、长度和混凝土强度等级的增长而增加，切断型钢纤维的增强效果要优于铣削型和钢带剪切型。

Methods The average dissecting force ( ADF) and interlamellar shear stress of each interspace in the media were measured using a tensile strength tester, and the the final shape-changed strength ratio of each layer was calculated before and after melting the tissue with collagenase and elastase.

方法测定人主动脉中膜各层间单位分离力、剪应力和胶原酶和弹力蛋白酶酶解前后主动脉壁各层的屈服形状改变比能。

Study on tension and block shear behavior of bolted single angle-gusset plates

单角钢螺栓连接节点板拉剪性能研究可变剪接，旁路剪接

Firstly, this paper does theoretical research when tension acts on the bolt tip, and derives the distribution law of the bolt shear stress and axial force, and defines three different bolt stress state.

首先，本文对锚杆端部受拉力时做了理论研究，推导出锚杆剪应力与轴力的分布规律，并定义了锚杆三种不同的受力状态。

Method of Estimating In-plane Shear S-N Curve of Unidirectional Laminate from Off-axis Tension S-N Curve

由单向层压板偏轴拉伸S-N曲线估算面内剪切S-N曲线的方法