shell temperature的例句大全

application of computer-based kiln shell temperature supervising system

窑筒体温度计算机监测系统的应用

When the thickness of asbestos board reaches 30 mm, the shell temperature could be controlled below 360 ℃, which is lower than the creep temperature of the shell material, and the thermal expansion stress of the shell is only 50% of that without asbestos board.

当石棉板厚度为30mm左右时，炉壳温度可以控制在360℃以下；低于炉壳材质的蠕变温度，炉壳所受到的热膨胀应力仅为没加石棉板时的50%。

Ltd. The calculation indicates that converter heat insulation layer thickness of asbestos board is about 30 mm. The converter shell temperature can be controlled within 360 ℃, which is lower than the creep temperature of shell material.

对重钢50t转炉进行了炉壳（炉身段）温度场分析，计算表明：转炉隔热层石棉板的厚度为30mm时，炉壳温度就能控制在360℃以内，低于炉壳材质的蠕变温度。

Review of infrared shell temperature measuring method on rotary kilns

回转窑表面温度红外检测法综述

Turbine Shell Temperature and Thermal Expension Models of A Powerplant Simulator

电站仿真器的透平金属温度与相对膨胀模型

Firstly, paper analyzes the signification of the aluminum tank shell temperature detection to aluminum technics and the health condition calculation of aluminum reduction cell. Research the status quo of the aluminum reduction cell shell temperature detection.

论文首先分析了铝电解槽壳温度检测对铝电解工艺及铝电解槽健康状况预测的重要意义，调研了铝电解槽槽壳温度检测的研究现状。

According to numerical simulation and molten steel solidification mechanism, in the paper, the restrict relationship had been setup between casting speed and molten steel level and average mould tapping section thickness as well as its shell temperature at tapping spout.

本文基于数值模拟和钢液凝固机理，建立起结晶器内钢液液位和铸坯拉速对其出钢口处钢液截面平均温度和坯壳温度的制约关系。

design for kiln shell temperature scanning system

回转窑筒体温度检测系统的设计

The design method of on-line shell temperature measuring system is introduced in this paper. It is emphasized to measure shell temperature with thermal couple and ADAM module here.

介绍了铝电解槽壳温度在线检测系统的设计方法，重点讲述了如何应用热电偶和ADAM模块进行温度采集和传送。

Testing and Analysis of Temperature Field of Camshaft during Solidification Produced by Shell Mold with Iron Shot Backing

壳型填铁丸工艺条件下凸轮轴凝固温度场测试及分析

In this paper, the mathematical model for steady heat conduction of a circular shell casing is worked out and solved to obtain the formulae for its temperature distribution and fin efficiency at the tip surface and lateral surface. The dimensionless curves are also plotted for engineering calculation.

拟定薄壳圆套管稳态导热的数学模型，求解得出其端面和侧面的温度分布及肋效率计算公式，并绘制了无量纲曲线，供工程计算用。

Temperature Distribution and Fin Efficiency at the Tip Surface and Lateral Surface of a Circular Shell Casing

薄壳圆套管端面和侧面的温度分布及肋效率

Traditional analytical method establish model with shell unit, the method ignore the thermal distortion from temperature gradient.

而传统分析方法是按壳单元建立模型，忽略了温度梯度引起的热变形。

The effect of different water groove design of the copper plates on the temperature distribution of the mold and the solidifying shell has been studied through thermo-mechanical coupled analysis.

通过对两种不同板坯水槽设计形式进行热力耦合分析，研究了不同水槽设计对结晶器铜板及铸坯初凝坯壳温度分布影响。

Large Amplitude Vibration of A Shallow Thin Conic Shell Subjected to Temperature Load

扁薄锥壳在变温条件下的大振幅振动问题

The results show that temperature gradient on the front edge of solidified shell in combined mold can be reduced and the proportion of equiaxial crystal of billet is more than 80%.

结果表明：复式结晶器能够降低钢液凝固前沿的温度梯度，从而使铸坯的等轴晶率超过80%。

According to the different time of degrading, samples 1-10 were extracted from bean sprout and orange shell, sterilized and stored in low temperature refrigeratory.

本研究以豆芽和桔皮为原料，用果胶酶降解后，得到1&10号提取液，高压湿热灭菌后低温冰箱保存。

The proposed method is applicable to measure the materials in powder, in shell, or under high and low temperature conditions.

文中提出的方法也可用于测试粉末状材料、薄板材以及材料的高温测试及低温测试。

Melamine, cashew nut shell liquid modified phenolic resin is a kind of resin resisting high temperature used in friction materials.

三聚氰胺、腰果壳油改性酚醛树脂是一种耐高温的摩阻材料用树脂。

Research on Thermal Stress Equivalent Static Load for Shell under Effect of Constant Temperature Field

常量定常温度场作用下壳体热应力当量静载的试验研究