shell temperature的例句大全

approximate analytical formula of roll shell's temperature field embracing external cooling effect in continuous roll casting

计及外冷效应的铸轧辊套温度场近似分析解

comparison between three methods for numerical simulation of temperature field in roll shell during twin-roll casting

铸轧辊辊套温度场数值模拟方法比较

numerical simulation of temperature field in roll shell under twin-roll casting

铸轧辊辊套断面温度场的数值模拟

study on the roll shell's temperature field in the high speed thin gauge twin roll casting for aluminum belt

铝薄带超常铸轧辊套温度场研究

a phenomenon following saint-venant principle in temperature field of roll shell during twin-roll casting

双辊铸轧辊套温度场分布的圣维南原理现象

test method for high temperature permeability of shell

型壳高温透气性试验方法

The main cause of deformation of a converter shell is temperature rising of the converter shell, a economical and effective method to reduce the temperature and creep deformation is adopting a heat insulation layer of asbestos board.

转炉炉壳温度升高是炉壳变形的主要原因，采用内衬石棉板隔热是降低中小型转炉炉壳温度、减轻炉壳蠕变变形的经济有效措施之一。

The surface temperature and the solidified shell thickness of round billet are strongly influ.

介绍了射钉法在测量连铸坯凝固坯壳厚度方面的应用情况.

Blast furnace shell will get into plastic stress and temperature distortion, and then thermal elasticity is inapplicability.

在炉壳温度较高或者炉内压力比较大的情况下炉壳会进入塑性变形状态，热弹性力学已不适用。

Soft-shelled turtle is alive, when the water temperature gradually, because it will be hot and soft-shelled turtle soup, sauce on the nature of soft-shelled turtles into the body.

甲鱼是活的，当水渐渐升温后，甲鱼就会因为热而喝汤，调料自然就进入了甲鱼的体内。

The pressure and temperature contour plot are drawn on the true oil-film form between shaft and bearing shell.

给出了以真实油膜形状作为基底的压力，温度三维等值线。

Internal expansion joint shall be adopted to single tube side float head heat exchanger for avoiding from large temperature difference stress, when design pressure on shell side is larger.

设计单管程浮头式换热器时，为避免较大的温差应力，在壳程设计压力较大的状况下，常采用内置膨胀节的形式。

The composition of core and shell monomers, the optimum amount of acrylic acid, nano-silicon sol and initiator, and optimum reaction temperature and dropping hour were defined.

确定了核壳单体组成，纳米硅溶胶、丙烯酸、引发剂等的最佳用量，以及最佳反应温度和滴加时间。

low temperature self-cross-linking formaldehyde-free binder for pigment printing is prepared by means of core-shell emulsion polymerization.

采用 核壳 乳液聚合的方法制备低温自交联的无甲醛涂料印花粘合剂.

A kind of three layered 32-node temperature shell element is presented for the transient temperature field FEM analysis of the honeycomb sandwich composite shell.

提出一种三层32结点温度壳单元，对蜂窝夹芯复合材料壳体的瞬态温度场进行了有限元分析。

The results show that temperature gradient on the front edge of solidified shell in combined mold can be reduced and the proportion of equiaxial crystal of billet is more than 80%.

结果表明：复式结晶器能够降低钢液凝固前沿的温度梯度，从而使铸坯的等轴晶率超过80%。

Billet temperature field and temperature gradient in the front of solidifying shell have been computed in condition of 2.4m/min casting speed for different secondary water strategy.

计算了小方坯连铸机在2.4m/min拉速、不同二冷配水下铸坯的温度场和凝固前沿温度梯度。

Tube and Shell Heat Exchanger Strength Research under Temperature Load

管壳式换热器温度载荷下的强度研究

Large Amplitude Vibration of A Shallow Thin Conic Shell Subjected to Temperature Load

扁薄锥壳在变温条件下的大振幅振动问题

Testing and Analysis of Temperature Field of Camshaft during Solidification Produced by Shell Mold with Iron Shot Backing

壳型填铁丸工艺条件下凸轮轴凝固温度场测试及分析