stress Testing的例句大全

On Suitable Testing Time of Blind Hole Technique for Measuring Residual Stress

盲孔法测定焊接残余应力适宜测试时间研究

FCGR will decrease with thicker sample and smaller stress ratio at the same testing condition.

在相同实验条件下，试样厚度越大、应力比越小，疲劳裂纹扩展速率越低。

The Failure Rate Function of Weibull Distribution in Progressive Stress Life Testing for the TFR, TRV and CE Models

TFR、TRV和CE模型序加试验下WEIBULL分布产品的失效分布

Researchers at Microsoft in Redmond, Wash., are testing how to deliver useful stress reduction tips.

位于美国华盛顿州雷德蒙德市的微软公司的研究人员正在测试如何提供有益的减压技巧。

Development of Testing Stress Device by LCR Ultrasonic Wave

LCR超声波应力仪的研制

Metal magnetic memory ( MMM ) testing method can find the stress concentration area.

采用磁记忆 无损 检测方法可以检测出应力集中区.

The experiments of the tooth root stress and noise testing have proved that the method is efficient for designing the high contact ratio gear set, and has some advantages of dynamic behavior and strength.

通过切齿、齿根应力测试、噪声测量等对比实验，验证了高重合度弧齿锥齿轮设计方法的可行性，证明了这种齿轮在动态性能与强度性能方面均有优越之处。

Examples are setup for stress and performance testing and preparation of a subject for usability testing.

例如压力和性能测试的启动以及可用性测试的准备工作.

Tensile stress-strain tests and tear strength were test by AIPU ALJ-02 tensile testing machine. 4.

使用AIPU ALJ-02型双数显拉力试验机对其进行拉伸应力应变测试、撕裂强度测试。

The full process testing curves of stress strain for the granite of the TGP permanent lock present typical elastic brittle plastic properties.

长江三峡花岗岩测试表明，其应力应变全过程曲线呈现典型的弹脆塑性。

The liquid capacity and liquid resistance in testing apparatus of endothelial cells' shear stress

内皮细胞切应力测试装置中的液容与液阻

He says the testing campaign may put additional stress on the health system, but that will show where the weaknesses are.

他说，这次检测活动将对医疗体系带来新的压力，但是也会揭示出薄弱点。

Then the testing method of constant stress Accelerated Reliability Growth Testing is given on the basis of AMSAA-BISE model.

再次，基于AMSAA-BISE模型给出了恒定应力下加速可靠性增长试验的试验方法。

All parameters used in the flow stress models were calculated based on the testing data.

采用建立的流动应力模型计算实验条件下的流动应力，计算结果与实验结果吻合较好。

Stress Analysis of Bearing Metal and Research of Testing Method for Fatigue Strength

合金轴瓦的应力分析与疲劳实验方法

Comparison Between Domestic and Overseas Standards for High-temperature Creep, Creep-rupture and Stress-rupture Testing of Metallic Materials

当金属在高温下受到应力时，就会发生蠕变。金属高温蠕变及持久强度试验国内外标准比较

METHODS: Post cores were divided into four groups according to their lengths and diameters. Slices of the models were observed and maximal shear stress of each testing point was calculated with 3 dimensional photoelastic stress freezing method, after vertical and oblique loading.

方法：根据桩的长短、粗细将实验分成4组，通过垂直和斜向加载，采用三维光弹性应力冻结法，经模型切片观察计算出模型各测点的最大剪应力。

In order to verify the analysis results, static test on two spatial full-sized solid models is carried out, and the step-by-step load apply system is adopted to find out the stress and strain value of each testing point.

为验证计算分析结果，对两个受力较大的铸钢节点进行了足尺实体静力试验，采用分级加卸载制度获取各级荷载下各观测点应力应变值。

During the bearing turning, the body of the bearing testing set receives the bigger load and generates larger deformation and stress.

在轴间轴承测试过程中，试验机机体承受较大的载荷并产生一定的变形和应力。

Design and fabrication of assembled testing unit of featured stresses and stress corrosion testing in wet h_2s environment

含应力特性试件的设计制作及湿H2S应力腐蚀实验