stress model的例句大全

Tide Stress of the Radially Heterogeneous Spherical Elastic Earth Model

球状径向不均匀弹性地球模型的固体潮应力

Stress distribution of the spine in upright, flexion and extension postion was analyzed using a three-dimensional finite element model of the spinal motion segment.

本研究采用脊柱活动节段的三维有限元模型分析了脊柱在直立位、前屈位和后伸位的应力分布情况。

Result The universal spine system in group which part of intervertebral disc removed in model of unstabilized lumbar suffered more stress and it was easy to fatigue ( P < 0.01);

结果：腰椎失稳模型中去除部分椎间盘组USS系统在轴向压缩、前屈、左、右侧弯及扭转运动上承受应力最大（P＜0.01）；

In order to simulate the residual stress and deformation of large-scale spiral casing of water turbine, the welding heat source model and the temperature field of multipass welding are studied in this paper.

为了对大型水轮机蜗壳的焊接残余应力和变形进行数值模拟，本文首先对焊接热源模型及多层多道焊的温度场进行了研究。

A fracture model of jointed rock mass is established considering the effect of horizontal seismic acceleration. Based on the proposed model, the relationship between the stress intensity factor, and length, spacing and dip of joints is discussed.

考虑了地震水平加速度的作用，建立了裂隙岩体的破裂模型，分析了在水平加速度作用下节理组的倾角、节理长度及间距对岩体破裂的影响。

A searching method of expected slide path in rock mass based on domain-divided statistics model of joints and the rock mass stress field is presented.

介绍了一种根据分区域结构面统计模型以及岩体在荷载作用下的应力场，在指定岩体结构区域内搜索出最可能出现滑移路径的方法。

Expected slide path method for stability analysis of rock mass based on statistics model of joints and stress field

基于结构面统计模型和应力场的岩体稳定性分析的期望滑移路径方法

In order to describe mechanical property of materials subjected to cyclic loading, the back stress was introduced in polycrystalline plasticity model. Furthermore, size effect was considered through slide resistance evolution function.

多晶塑性模型中通过引入背应力考虑循环载荷下材料力学行为响应，而且，在滑移阻力函数中考虑了材料的尺寸效应。

The model considers the forces acting on sliding bed in inclined pipe, shows approximate estimates of the pressure distribution and average concentration, and ignores shear stress between water lying in the clearance of solids and pipe wall in sliding bed.

该模型在考虑倾斜管道滑动床的受力情况的同时，对滑动床的压力分布、平均浓度作了一定程度近似估计，并且忽略了滑动床颗粒间隙中的水与管壁之间的剪切力。

The deformations in the contact slice of the model consist of two parts i.e. shear deformation and sliding deformation. For the normal constructive model, the nonlinear model between the normal stress and normal relative deformation was adopted.

该模型将接触带内的变形分为剪切变形与错动变形两部分，对于法线方向采用法向应力与法向相对变形之间的非线性模型。

Defining the Calculate Model about the Soil Stress Under the Under-Reamed of the Push-Extend Multi-Under-Reamed Pile by Using the Theory of Sliding Line

运用滑移线理论确定挤扩多盘桩盘下土体应力计算模式

Reliability design of the mechanism of sliding leadscrew nut is studied by using the stress strength interference model.

应用应力-强度干涉模型，研究了滑动丝杠螺母机构的可靠性设计。

On basis of the wafer twist and slip model, the stress state of the small slice are studied.

结合晶片扭曲和滑移的模型，分析了小晶片的受力状况。

Secondly, the choice of boundary material and the matching of boundary effect of the test model of deep hole bench blasting are analyzed by utilizing stress wave theory. At the same time the results of experiments were applied to the project practice.

然后利用应力波理论，讨论了深孔台阶爆破试验模型的边界材料的选择和边界效应匹配问题，同时将实验结果应用到了工程实际中去。

Artificial Neural Network Model to Predict Yield Stress of Waxy Crude Oil

人工神经网络预测含蜡原油的屈服应力

Finite element numerical solution of fatigue life of mechanical member and of stress intensity factor K and J-integral for 3D model is approached with ANSYS software. An important method is made for the fatigue analysis and fatigue performance of winder axle.

本研究探讨了利用ANSYS软件分析机械构件疲劳寿命和三维模型断裂参量K和J积分的方法，为提升机主轴的疲劳分析和断裂性能研究提供了一种重要手段。

objective to investigate the change of actin filament in rat model of stress urinary incontinence and to certify the relationship between sui and the dysfunction of pelvic floor.

目的观察大鼠压力性尿失禁（SUI）时盆底肌肉微丝形态和结构的变化，探讨盆底肌肉功能障碍的原因。

the molar model revealed that the tensile stress concentration was at the mesial root cervix and the compressive stress was at the distal root cervix.

左下颌第一磨牙牙根表面、牙周膜、牙槽骨所受的最大拉应力均位于近中侧牙颈部，最大压应力位于远中侧牙颈部；

A three layer cylinder model containing alloy, steel lining and housing was established. With the help of finite element method ( FEM) software package ANSYS, and considering the stress change along alloy thickness, the bearing stress especially in alloy layer was calculated.

建立了合金层、钢背和轴承座的三层圆筒模型，利用ANSYS软件对轴瓦应力，尤其是合金层应力进行了计算，计算过程中考虑应力沿合金层厚度方向的变化。

The Wellbore Breakage Simulation by Mechanics/ Chemistry Coupling Model; Design Norm of Fatigue Strength of Combination Stress in Cylinder of Injection moulder

力&化耦合作用下井眼破坏过程模拟注塑机筒复合应力疲劳破坏的设计准则