surface force的例句大全

The prepared ink has good solution viscosity , surface force, solvent resistance and adhesive capacity.

墨水溶液粘度 、 表面张力及耐溶剂性能、粘附性能均较佳.

Unique disassembly design, single surface force avoid the broken of cell glass.

特殊的剥离设计, 单面受力,保证不会因拉力过大对玻璃基板产生致命的损坏.

The Interface Layer Model and Surface Force

界面层模型和表面力

Using ordinary pressure plasma, choose different processing power continuous dynamic treatment on aramid fiber surface, using scanning electron microscope and atomic force microscope to show its surface characterization, dynamic contact Angle apparatus can test its surface wettability.

采用常压等离子体，选择不同的处理功率对芳纶纤维表面进行连续动态处理，通过扫描电镜以及原子力显微镜对其表面进行表征，动态接触角仪对其进行表面润湿性能测试。

Tectonic force source and seismic source stress field investigation on the coating's static shear stress and surface tension

构造力源和震源应力场涂料静切力及表面张力的研究

By energy transition principle of elastic mechanics, the physics relation between strain around fault and tectonic force on fault surface is set up and main body element model of crust strain is put forward.

利用SCHOLZ断层能量动态平衡过程，建立了断层周边应变累积与断层面构造力的一般物理关系，据此提出以断裂带为主体的地壳应变主体单元模型。

The maximum anchorage force of the manipulator is 450 kN, and every part of the manipulator is no higher than rail surface in non-operating mode.

机械手最大锚定力为450kN，在非工作状态时设备最高点不高出轨面。

The contact angles of the F-DLC films deposited on glass substrates with water, the bond structure and the roughness of the films were investigated by surface tension measure apparatus, FTIR, and atomic force microscopy, respectively.

接触角测量仪测量了沉积在玻璃基底上的F-DLC薄膜的接触角，采用傅里叶红外分析了薄膜价键结构，原子力显微镜分析了薄膜表面粗糙度；

Measurement of the surface tension coefficient of liquid with force sensor

用力敏传感器测量液体表面张力系数

The results showed that: in most cases, the spreading of these surfactants was driven by the unbalanced capillary force on the three-phase contact line, and that surface tension gradient participated the spreading process of surfactant I, ⅱ with higher concentration.

结果显示：在大多数情况下，葡糖酰胺类三硅氧烷在石蜡表面的铺展是由三相线处非平衡毛细作用力导致，在高浓度的I，II体系中，表面张力梯度参与驱动液滴的铺展。

The surface roughness of microlens is measured by an atomic force microscope ( AFM-ⅱ). Micro-lens forming mechanics has been analyzed by surface tension theory.

用AFMⅡ型原子力显微镜测得微透镜阵列的表面粗糙度Ra约等于0.9nm，并通过液体的表面张力理论分析了微透镜的形成机理。

The distribution patterns of axis force is close to the ladder type. Upper soil surface for the linear is straight, the mud below the surface for the linear is decline, and has a terminal resistance.

轴力分布模式接近梯形分布，泥面以上为直线段，泥面以下为线性递减，并具有一定的端阻力。

The cutting force and the thermoplastic shear instability can directly influence on machining precision, tool life and surface roughness.

在加工中切削力的变化和热塑剪切失稳的发生将直接影响加工精度、刀具磨损和表面质量。

Through cutting experiment, the influence on cutting force and surface quality was analyzed when change the parameters such as cutting speed, back cutting depth and cutting fluid and so on.

通过切削试验，分析了切削速度、背吃刀量以及切削液等参数改变时，对切削力及表面质量的影响。

Finally, analyzed main tunnelling parameters such as tunnelling velocity, grouting pressure, thrust force of the jack and the relationship between chamber pressure of the NO.3 stress point with surface settlement based on the project examples.

最后结合成都地铁1号线2标段工程实例，分析了盾构施工主要施工参数如：掘进速度、注浆压力、千斤顶推力、3号应力点土仓压力和地表沉降的关系。

This paper investigates forces applied on port plate surface of point contact axial piston motor, and introduces a solution of the problem of additional tilting moment of the cylinder body caused by applied force not on supporting point.

本文通过研究点接触式轴向柱塞马达配流面的受力情况，介绍了运用静压平衡理论设计平衡油室的办法，解决缸体上存在的由于作用不在支承点上所造成的附加倾复力矩的问题。

Surface structure of dental filling material investigated with Atomic Force Microscope

应用原子力显微镜观测牙齿充填材料的表面结构

Based on the theory of vector spherical harmonic functions, this paper discusses influences of the tidal generating force, and the surface stress on the earth deformation as well as the incremental gravitational potential.

本文基于矢量球函数的基本理论，讨论了引潮力和地表应力对地球形变和引力位增量的影响。认为地球潮夕形变和负载形变只有球形场位移，而没有环形场位移。

The pictures and quantitative information on ferroelectric domain and etch pits of dislocations in etched KTA crystal surface have been given first time by atomic force microscope.

首次用原子力显微镜给出了用两种腐蚀剂腐蚀过的KTA晶体表面的铁电畴和位错蚀坑的照片及定量信息，如发现铁电畴的明区要高于暗区，且两者的粗糙度明显不同。

Using acetylene torch to make tin pewter welding rod melting and bonding with the tin surface to improve the bonding force.

采用氧乙炔火焰将锡锑轴承合金焊条熔化结合在锡表面，以提高两者的结合力。