surface load的例句大全

Abnormal distribution of load on talus articular surface was an important factor of ankle joint disease, such as osteoarthritis.

距骨各关节面的载荷分布异常是踝关节关节疾病发生的重要因素，是发生骨关节炎的主要病因之一。

As compared to montmorillonite, the total surface area, micro-pore surface area and micro-pore volume of copper-loaded montmorillonite are reduced, while the cation exchange capacity, external surface area, pore volume and pore diameter are increased.

与蒙脱石相比，载铜后的蒙脱石总比表面积、微孔比表面积、微孔体积减少，而离子交换容量、外比表面积、孔体积和孔径增大。

Secondly, for K8 latticed shells, the second-order inelastic analysis, considering material and geometric imperfections, is carried out to obtain the limit load. Finally, the Monte Carlo simulation on the response surface is applied to statistical study of the resistant factor.

然后选择应用最广的K8作为重点对象，使用基于响应面函数的蒙特卡罗模拟方法对结构进行考虑初始缺陷的二阶弹塑性分析，得出了抗力分项系数。

TICs'surface solar absorptivity and emittance are the dominant factors to the cooling load;

涂层表面太阳吸收率和发射率对空调负荷的影响非常大，是起主导作用的因素；

A modified Vlasov two-parameter soil model in Gibson soil is developed and the corresponding soil response function is derived. The stresses and the surface displacements of the soil subjected to a line load and a uniform strip load are analyzed.

对Gibson土中的Vlasov双参数地基模型进行了改进，导出了相应的特征函数，并就集中及均布条形荷载下土中内力及地面位移进行了分析。

The structure of Pd-Cu-Si alloy with Ni-P amorphous plating and its slide friction property were studied. It was indicated that the effect of load on the wear capacity was not obvious and the hardness of the wearing surface dose not increase during the wearing test.

用X－射线衍射研究Pd－Cu－Si合金玻璃丝和Ni－P非晶态镀膜摩擦付的结构，及其滑动磨损特性，表明负荷对磨损影响很大，磨损试验中，硬度没有增加。

At higher temperatures the load carrying capacity is reduced, depending on the material and sliding contact surface combination.

在温度较高的情况下，负荷能力会降低，降低幅度视材料和滑动接触面组合而定。

The wear characteristics of polytetrafluoroethylene ( PTFE) were tested on the model MPX-200 pin-on-disk tester in this paper. The effects of sliding speed, load, temperature and surface roughness of counterparts on wear were determined.

作者用MPX-200型栓-盘摩擦磨损试验机测试了模压聚四氟乙烯的磨损性能，考察了滑动速度、负菏、温度及偶件表面粗糙度对磨损的影响。

With the increase of the sliding speed and the normal load and with the prolonged sliding time, the surface temperature was elevated.

干摩擦时3Y-TZP表面温度随速度和载荷的增大而升高，且随滑动时间的延长而升高。

The friction oxide generated in the wear surface, and the degree of oxidation increased and aggravated with the increase of load and sliding velocity.

磨面随着摩擦的进行氧化现象明显，氧化程度随着载荷及滑动速度的增加而加剧。

The shape and location of the slip curve surface, the ultimate bearing capacity under load were found out when the high fill embankment on slope foundation was under unstable condition.

结合山区高速公路建设的实践，采用足尺模型试验，得出荷载作用下斜坡地基上高填方路堤滑动破坏面出现的位置及形态，并测定了其相应的极限承载力。

It is different from under point contact that there is no stick area under line contact in the partial slip regime, and load distribution within line contact area is uneven due to roughness of surface.

磨痕分析表明，承载区域接触不均匀，存在虚接触区域，其大小与表面粗糙度有关，而接触区域没有不磨损的粘着区，不同于点接触形式。

Problems as low combustion efficiency, bad part-load operating performance, too much pollutants emission, and high temperature corrosion and slugging on water wall surface occurred in many domestic coal fired boilers.

国内相当一部分燃煤锅炉存在燃烧效率低、低负荷稳燃性能差、污染物排放量大以及炉膛水冷壁易结渣和高温腐蚀等一系列问题。

Submarine-launched Harpoons are pre-loaded into a capsule and launched from a torpedo tube. The capsule rises to the surface and launches the missile.

潜水艇把发射的鱼叉预先放入胶囊，从鱼雷发射管射出，胶囊上升到表面，发射。

Bounding Surface Elastoplastic-viscoplastic Analysis on Soft Clay of Heaped Load Precompression

超载预压软基固结边界面弹塑/粘塑性分析

The simple bounding surface elastoplastic-viscoplastic model was used in Biot' consolidation theory. The deformation and pore pressure of road soft clay improved by heaped load precompression was calculated numerically.

在Biot固结理论中使用简化的边界面弹塑/粘塑性模型，对超载预压法处理公路软基全过程的变形和孔压进行数值计算。

Thus it can be seen that the surface treatment of corrugated wire gauze packing has more advantages under a low liquid load.

由此可见，在低液体负荷下，金属丝网波纹填料的表面处理更具有优越性。

Many properties, such as friction coefficient, load support capacity, lubricant flow, load support angle, etc, can be changed and optimized by changing the slippage property of the bearing surface.

通过改变轴套表面的滑移特性可以改变和优化轴承的各种性能，例如摩擦系数、承载力、润滑剂流量、承载角等。

The results showed that the serious damage appeared at the position of the dam back near the load range where the dam surface is much easer to damage.

研究表明，爆炸载荷作用附近以及其对应坝体背面的相应位置最易发生损伤破坏；

Load factor of the wearing quantity of the tooth surface was obtained in the test research.

通过实验研究，得到了齿轮轮齿表面磨损量的载荷因子。