surface stress的例句大全

Surface and interfacial stresses are slightly affected by FeAl layer. Therefore, when choosing thick ceramic layer and thin Al layer, there are appropriate stress distributions at surface and interfaces, and the mechanical properties of coatings can be strengthened.

FeAl层对表面应力和界面应力影响较小.因此，当选择较厚陶瓷层和较薄铝层时，涂层内将具有较优的表面和界面应力分布状态，从而可提高涂层力学性能。

the cross star structure is a kind of superficial structure, which occurs in the dipping steeply rock nearby its surface, and has formed by the effect of tectonic stress and gravity at the same place but not at the same time for its different parts.

研究表明，十字星构造是构造应力和岩体重力复合作用的产物，是一种发生在陡倾岩层临空部位的表生构造。

The cyclonic stress on the sea surface and the strong mixing processes forced by the typhoon play an important role in the processes of the heat, energy and mass exchange between the upper ocean and the deep ocean.

台风产生的海面气旋式风应力以及强烈的混合过程，对上层海洋与深层海水之间的热量、能量和物质交换产生重大影响，因此研究海洋对于台风过程的响应特征具有重要的科学意义。

Influences on surface deformation by the three different stress source models in volcanic area

三种压力源模型对火山区地面变形的影响

Analysis of thermal spray particle's residual stress after deposit and curdle on the substrate's surface

热喷熔滴在表面沉积凝固后的残余应力分析

Off load rock mass of excavated slope can be divided into 3 zones: surface loose zone, off load deformation zone and stress adjustment zone.

开挖边坡卸荷岩体可为3个带：表层松动带、卸荷变形带以及应力调整带。

The contact element method and original stress method were used to analyze the elastic plastic contact problem of wheel/ rail with measured surface micro roughness. The distribution of surface contact pressure on the rail was obtained.

采用接触单元方法，结合初应力法，采用测量获得的表面微观粗糙度，对轮轨弹塑性接触问题进行了研究，获得了轮轨的表面接触压力分布等结果。

Under adequate water stress condition, the young field grapevine surface of leaves are dealt with betaine and FA, the effect is not obvious.

在非水分胁迫条件下，对田间葡萄幼树进行处理，叶面施用甜菜碱和FA旱地龙后对葡萄新梢生长无显著影响；

The amount of deformation and tooth contact line stress curves are extracted from the finite element calculation results. That is used to understand the contact stress distribution of the whole tooth surface in the process of contact. And the main areas of modification are determined.

提取了有限元计算结果的变形量、全齿面接触线应力曲线图，以了解全齿面在整个接触过程中的应力分布情况，确定修形的主要区域。

And the three dimensional surface of stress-strain relation in the whole stress field ( p, q) were drawn through visualization.

通过可视化绘出了在整个应力场（p，q）中的三维应力-应变关系曲面和屈服轨迹。

The profile, internal stress, cold-bending cracks and surface flaws of the hot strip have been analyzed, and the corresponding strategics and resolutions are also preferred, In order to improve the.

从宽带钢板形、内应力、冷弯裂纹及板带表面缺陷等几个方面进行了分析，并提出了相应的对策和解决办法。

In this paper, an electric device is proposed to measure contact stress on the sealing surface of sealing elements.

介绍了西北工业大学研制的密封面接触应力的电测装置。

The software mainly includes four functions: contact stress simulation module, wear simulation module, surface morphology and debris morphology simulation module, and data management module.

该软件包含接触应力仿真模块、磨损量仿真模块、磨损表面形貌和磨粒形貌仿真模块及试验数据管理模块四个部分。

When a micro interfacial stress is applied to the novel surface acoustic wave interfacial stress sensor, the input-output of the sensor is a simple linear function. We built the linear regression model and solved it by the least squares method. 4.

当新型声表面波压力传感器加载微压力时，其输入输出函数是一元线性函数，所以只需建立其一元线性回归模型，并利用最小二乘法求解即可。

The result shows that: the stress/ strain in straightening roller that contacting with the bloom is the largest, and reducing from the surface to the centre of bloom in turn. 3.

研究表明：应力/应变在拉矫辊与铸坯接触处最大，并由铸坯表面向铸坯中心依次减小。

It is to use finite element method to calculate the stress within the slope in this paper, and get the normal stress and tangent stress of the slope sliding surface directly, and then calculate the stability coefficient of the slope.

本文研究内容是应用有限元法计算斜坡内部的应力，并直接求解边坡滑动面上的法向力和切向力，进一步计算边坡的稳定系数。

3D deformation pattern picture, the stress and strain of tube surface and regularities of distribution of spinning force during the process of three-roller synchronous hot backward spinning are investigated.

研究了三轮同步热反旋过程中的三维变形图，管坯表面应力、应变以及旋压力分布规律。

Contact force generated by particles imposing on the surface of material can form contact shear stress and radial tensile stress.

材料表面受到颗粒冲击产生的接触压力形成接触剪应力，以及在接触边界上产生径向拉应力。

The von Mises stress and distribution scope were difference in different phase. The von Mises stress in the talar dome, talar neck, talonavicular joint surface gradually increased, and decreased in the subtalar joint. 3.

不同位相距骨VON MISES应力值及分布范围不同，等效应力在距骨滑车、距骨颈及距舟关节从落地相到离地相逐渐增大，在距下关节逐渐减小。

When the side surface is under simple shear load and has a tangential deformation, stress concentrations occur at the fixed end of yarns which are the main load-bearing bodies.

当模型的侧面受到简单剪切而产生切向变形时，在主承载纤维束的固定端产生应力集中。