temperature optimum的例句大全

The optimum process conditions of surface modification of wollastonite were suggested as follows: modification reagent stearic acid, modification reagent dosage 2%, modification time 15~ 20 min, modification temperature 70 ℃.

通过对超细硅灰石粉体的表面化学改性效果的研究，确定了最佳工艺条件：改性剂为硬脂酸，改性剂用量2%，改性时间15~20min，改性温度70℃。

Added accelerant calcium alkylphenol and methylic acid separately and calcium hydroxide group by group into the reaction, the optimum temperature and time of neutralizing reaction is 70~ 80 ℃ and 10 min, the optimum temperature of carbonation is 50 ℃.

通过在反应过程中分别加入促进剂烷基酚钙和甲酸以及分批次加入氢氧化钙，中和反应最佳温度70-80℃，反应时间10min，碳酸化反应最佳温度50℃。

Under certain pressure and space velocity conditions, the optimum H2/ N2 was different for different reaction temperature.

在压力和空速一定的条件下，最佳H2/N2随反应温度而异。

Influences of reaction temperature, hydrogen pressure, space velocity and hydrogen/ oil ratio were investigated and optimum condition was obtained.

研究了加氢精制的工艺条件，考察了反应温度、氢压、体积空速和氢油比对聚α-烯烃合成基础油加氢效果的影响，确定了最佳的加氢精制工艺。

The range of temperature for fruit body differentiation was 13-22 ℃, and the optimum was 19 ℃.

子实体分化的温度范围13&22℃，最适温度19℃；

The range of temperature for mycelial growth was 10~ 25 ℃, the optimum was 20 ℃;

孢子萌发的温度范围是10~25℃，最适温度20℃；

Catalyzing function of chloroplatinic acid is not obvious at lower temperatures and the optimum catalyzing cross-linking temperature is above 150 ℃.

氯铂酸催化剂在低温下催化作用不明显，催化交联的反应温度在150℃以上。

β-sitosterol. 2. The optimum extracting condition of Rubia yunnanensis Diets, is: 8 times amount of 70% ethanol, and refluxing at the temperature of 80 ℃ for 90 min twice.

小红参最佳提取工艺为8倍量70%乙醇，于80℃下，提取90min，共2次。

Peroxidase ( POD) in the spring leaf of orange cv. Jincheng ( Citrus sinensis Osbeck) was extracted. The optimum pH, optimum temperature, Km, Vmax and common inhibitors for POD were analyzed.

以锦橙成熟春梢叶片提取过氧化物酶（POD），分别测定了该酶的最适pH、最适温度及酶促动力学参数Km值和Vmax值，比较分析了常见几种POD抑制剂的作用程度。

The optimum pH, temperature and shaking speed of xanthate-degrading are 8.0,30 ℃ and 120 r/ min, respectively.

菌株降解黄原酸盐的最佳条件为：pH为8，温度30℃，振荡速率120r/min。

the optimum reaction condition were as follows: ultrasonic power 175 w, ultrasonic radiation time for 30 min, ultrasonic radiation temperature at 40 ℃ and iodine as inducer.

反应的最佳条件为：碘单质作诱导剂，超声波功率为175W，反应时间为30min，反应温度为40℃。

this paper studies the optimum formulation of the preserving solution used for the liquid storage of fresh kiwi fruit slices at normal temperature and the key technology conditions of desalinization, coloring and saccharification of the processed preserved fruits with the fresh kiwi fruit slices as the raw material.

研究了常温下液藏鲜切猕猴桃片的保鲜液最佳配方与以其为原料加工果脯的脱盐、上色、糖制等关键工艺条件。

Study on optimum kneading temperature of carbon paste

糊料最佳混捏温度研究

In this study, aphanitic graphite ore was purified in a melting process at high temperature and the optimum conditions were ascertained.

采用高温熔融法对隐晶质（土状）石墨进行了研究并确定了最佳工艺条件。

Under the optimum condition of high pressure and temperature treatment and storied at4 ℃ for10weeks, the microbial count of spiced beef was still lower than the specified value of national hygienic standard. Lactic acid bacteria and pseudomonas were dominant spoilage organisms.

将经过优化的高压条件（454.7MPa，16.8min，45.5℃）处理酱牛肉并冷藏10周后，其微生物总数仍低于国家卫生标准规定值，其中乳酸菌和假单胞菌为优势腐败菌。

Experimental results showed that the optimum temperature for spherulite growth of Nylon-1010 is between 150 and 175 ℃.

结果表明，尼龙-1010（Ⅰ）在150～175℃之间为球晶生长的最适宜温度。

Shakedown Optimum Design of Plates by Temperature Parameter Method

温度参数法用于薄板的安定优化设计

The paper introduces the effect of plating voltage, temperature and relative speed of electrodes to deposit rate and recommends an optimum technical regulation for the electrolyte.

研究了施镀电压、温度、电极相对线速度等工艺参数对镍铁合金刷镀沉积率的影响规律，提出了合理的施镀工艺规范。

The purification effect of five macroporous adsorptive resins on red cabbage pigment is studied in this paper, and the optimum resin type, adsorption temperature and adsorption time as well as the optimum eluting solvent and eluting temperature are hence determined.

研究了五种大孔吸附树脂对紫甘蓝色素的纯化作用，确定了色素纯化的最适树脂、吸附温度和时间，以及解吸的溶剂和解吸温度。

In order to improve productiveness, the liquid temperature should be maken arrive predetermine value as short time as impossible, and controlling accuracy should be ensured at the same time. For the purpose, an optimum scheme of dynamic heating in all process is presented.

在确保恒温精度的同时，为了在尽可能短的时间内使液体温度达到预定的温度，以提高工作效率，提出了全程动态加热方案。