tolerance analysis的例句大全

The prediction of waterlogging tolerance candidate genes by integrating expression and linked analysis data on Zea mays

整合玉米基因表达与遗传分析资料发掘耐渍性候选基因

The method for analysis and comparison of level of the standard gauge tolerance for normal products of the cold rolled steel sheets is put up.

提出了一种冷轧薄钢板常用产品标准厚度公差水平进行分析比较的方法。

The results indicate that the damage tolerance behavior of composite laminates can be taken fully by taking the impact threats into consideration in the reliability analysis.

研究表明，通过在可靠性分析中引入了冲击威胁的概念，可以较充分地发挥复合材料层压板的损伤容限性能。

Test Point Selection of Tolerance Network Based on Testability Analysis

基于可测性分析容差网络测试点选择

the interval parameter back analysis program is developed based on the flexible tolerance method.

基于可变容差优化反分析法,开发了区间优化反分析程序.

A Neural Network Approach to Fault Location of Tolerance Network Based on Testability Analysis

基于可测性分析的容差网络故障定位的神经网络实现

Analysis and measurement of the thickness tolerance in radiographic testing

射线检测厚度宽容度的分析与测定

Analysis and Design of Optimal Bus Fault Tolerance of Multibus System

多总线系统的最优总线容错性分析与设计

Appraisal of Alkali Tolerance Idioplasm of Maize at Seedling Stage and Analysis of Heredity of Partial Characters under Salt Stress

玉米苗期耐碱种质资源评价及盐碱条件下部分性状遗传分析

It draws a conclusion from the test data and energy analysis: If the mass tolerance and volatilization value is reasonably controlled, the combustible cartridge case has little effect on muzzle velocity error, and it is not worse than the metal cartridge case or bag charge.

根据试验数据及能量分析得出结论：合理控制可燃药筒质量公差及挥分值，可燃药筒本身对初速或然误差的影响是很微小的，甚至不比金属药筒或药包装药差。

Mathematical analysis for the diameter tolerance of spiral welded pipe

螺旋焊管直径公差的数学分析

Machining Tolerance of Piston Pin End Surface by Analysis and Calculation Method

分析计算法确定活塞销加工余量

Simulation Analysis of Error Tolerance Characteristic of the Thin Film Narrow Band-pass Filter for DWDM

DWDM用薄膜窄带滤光片的容差特性模拟分析

Process Analysis and Experimental Study on out of Tolerance of Sealing Performance of Cylinder Head Combustion Chamber

缸盖燃烧室密封性能超差工艺分析和试验研究

With the analysis of the water, the soil and Typha latifolia ′ s tissue in the purification pond system and. in the control, this paper indicated that Typha latifolia has an excellent ability in tolerance, absorption and assimilating Pb and Zn.

本文通过对净化塘系统和对照点的水、土和宽叶香蒲组织的分析结果指出：宽叶香蒲具有较强的忍耐、吸收和积累Pb、Zn等重金属的能力。

Monte Carlo simulation can obtain the range of the controlling precision for the film thickness, tolerance on the thickness of the each layer was obtained by dynamic sensitivity analysis;

Monte Carlo模拟能够得到膜系所要求的膜层厚度控制精度范围，膜系的相对灵敏度分析可以指明每层膜对误差要求的苛刻程度；

The Main Geometric Tolerance in the Nipper Plate Mechanisms Dynamics Analysis

计入主要形位公差的钳板机构动力学分析

The cause of false junks, the determination of tolerance zone and the false junks zone formulations of multi-loop size of chain were give under the analysis of a example.

对零件产生假废品的原因进行分析，提出了基于极限尺寸窜动的假废品判别方法，并指出了零件假废品出现的区域、零件假废品区域同基准不重合误差的关系。

Statistical Analysis to the Quality of Tolerance Examination Paper

公差试卷质量的统计分析

Identification and Analysis of Rice Drought Tolerance Using Near Infrared Diffuse Reflection Spectra of Leaves

栽培稻叶片近红外光纤漫反射光谱的抗旱性鉴定分析