tooth gear的例句大全

This paper introduces the developing of a cylindrical gear drive with dual convex-concave mesh& the bidirectional circular tooth gear drive.

本文开发研究了一种具有双重凸凹啮合的圆柱齿轮传动&双向圆弧齿轮传动。

Theoretical Study on Swing Sliding-tooth Gear Pump

摆动活齿泵的理论研究

study on mesh theory of roller oscillating tooth gear drive and numerical value simulation of tooth profile contact area

滚柱活齿传动的啮合理论及齿廓接触区数值仿真

On the basis of researching on sliding-tooth transmission theory and the principle of orbit motor, a new type of bolt sleeve sliding-tooth gear motor is presented. The discussion is focused on the working and structure principle of the new motor.

在活齿齿传动理论和行星摆线齿轮马达工作原理相结合的基础上，提出了一种新型的活齿液压马达，讨论了该活齿液压马达的工作原理。

development and experimental research on roller oscillating tooth gear reducer

滚柱活齿减速器的加工与实验研究

Research on Kinematics Analysis and Sliding Ratio Calculation of Cylinder Dual-Sine Oscillating Tooth Gear Reducer

圆柱双正弦活齿传动运动学分析及滑动率计算

Fuzzy Reliability Design of Circular-Arc Tooth Gear Driving for Roller Mill

辊磨机圆弧齿轮传动的模糊可靠性设计

oscillating tooth gear pair with small teeth difference

活齿少齿差齿轮副

fault tree analysis of roller oscillating tooth gear drive

滚柱活齿传动的故障树分析

machining stub tooth gear with standard gear hober

用标准齿轮滚刀加工短齿齿轮

Bidirectional Circular Tooth Gear Drive

双向圆弧齿轮传动

modeling and simulating of meshing for roller oscillating tooth gear drives

滚柱活齿传动的啮合建模与仿真

The transmission part is an involute gear, and the working part can adopt different working faces, such as a cylinder excircle face, a circular arc tooth or an involutes tooth gear top cavetto.

传动部分是渐开线齿轮，工作部分可采用不同的工作面，如圆柱外圆面或圆弧形齿或渐开线齿轮齿顶修圆。

characteristic analysis of non-contact parallel-axes permanent magnetic gear we also investigate the characteristic curves of torque-angle of straight tooth gears when their shafts have different alternate angles.

计算了直齿永磁齿轮在不同交错角下的矩角特性曲线，分析了交错角对直齿永磁齿轮传动转矩的影响，探讨了气隙对交错轴直齿永磁齿轮的影响。

Study of the Design of Tooth Width of Right Shaft angle Face Gear Drive

正交面齿轮传动中齿宽设计的研究

The algorithm and formulas to determine the size of tip relief modification of pre shaving gear hobs are put forward. A principle to determine the lead width of tooth roots is also presented.

给出了剃前齿轮滚刀修缘尺寸的计算方法和计算公式，并对滚刀齿根的齿间槽宽提出了更为合理的判断原则。

A systemic analysis has been made for meshing properties of the straight conjugating internal gear pair in this paper, involving the solution of conjugated tooth profile, meshing process and line of action, as well as the influences of gear designing parameters on the contact ratio.

对直线共轭内啮合齿轮副的啮合特性进行了全面分析，包括共轭齿形的求解、啮合过程分析和重合度计算及齿轮参数对重合度的影响等内容。

Gear tooth tip relief based on standard hob

基于标准齿轮滚刀的齿顶修缘

While the changing gear is selected by continued-fraction approach method and calculated by the aid of computer, the error in transmission ratio and tooth curve could be obviously reduced, the machining accuracy of gears can be enhanced and the time for selecting changing gear shortened.

采用连分数逼近的方法，借助于计算机辅助计算，大大降低了传动比误差及齿向误差，提高了齿轮加工精度，并可缩短挂轮选配时间。

By means of sticking the electric-resistance strain pieces on the transverse of the planetary gear, we have done the dynamic test of contact tooth pair numbers of the involute planetary transmission with mi-nor tooth difference in which the internal gear is used as the output member.

我们采用在行星轮端面贴电阻应变片的办法对内齿轮为输出构件的渐开线少齿差行星传动进行了接触齿对数的动态实测。