torque angle的例句大全

So torque angle control is the most important factor to solve the above problems.

因此，转矩角控制是至关重要的因素。

A permanent magnet synchronous motor servo system based on torque angle control is proposed in this paper.

在矩角控制的基础上，提出了永磁同步电动机的定位控制方案。

Tighten central screws on the sprocket and camshaft controller to the prescribed final torque using a torque angle wrench.

用扭力角度扳手将链轮和凸轮轴控制器上的中央螺钉拧紧至规定的最终力矩。

The simulations of instantaneous driving torque show that the instantaneous driving torque is changed between the positive and the negative and fluctuated highly at the angle of the valve plate(θ≤ 15 °), which result in the dead movement zone and the worse low-speed stability.

瞬时扭矩的仿真分析表明，在θ≤15°时，其瞬时驱动扭矩在正负值之间跳动，脉动率高，是其产生低速稳定性差、存在运动死区的主要原因。

In the present paper, the J integral was estimated from the relation between torque and twist angle of a cylindrical bar with a deep circumferential crack.

研究了扭转载荷下带环状裂纹圆棒试样的J积分的评价。

The model analyses and identifies the EMG of human muscle, joint angle and joint torque signal, in order to get access to biomechanical model.

选用反映人体肌肉收缩的肌电信号、关节角度和关节力矩等信号，进行模型的分析辨识。

Curves that each joint angle, joint moment and nonlinear twist spring's torque with the time in the process are obtained using Matlab, and discussed contrast to linear joint.

并从袋鼠腿部的生物构造，引入了非线性刚度表达的柔性关节，通过与线性关节模型对比，探讨了踝关节非线性对其关节力矩和起跳性能的影响。

A Direct Torque Control for Induction Motor Based on Amplitude and Angle Control

基于定子磁链幅值和角度控制的异步电机直接转矩控制

Through lead angle control the electric-magnetic torque reaches maximum value.

通过超前角控制，使电磁力矩达到最大值。

Firstly, the CNG engine torque control theory is introduced, and the relationship between the engine output torque and the three control parameters: the spark advance angle, the air-fuel ratio and the throttle opening, is derivated.

首先，研究天然气发动机转矩控制理论，推导点火提前角、空燃比和节气门开度三个控制参数与转矩之间的关系。

when the camber and lateral angle are of same sign, lateral force is promoted, and cornering torque is suppressed.

当侧倾角与侧偏角同号时，侧向力被促进，回正力矩被抑制。

industry: torque wrench; assembly type pneumatic tools; riveter; other pneumatic tools; angle grinder; diamond tools;

所属行业：扭力扳手；装配类气动工具；拉铆枪；其他气动工具；角磨机；金刚石工具；；

with close-loop adjusting ignition advance angle controlling the torque fluctuating, it realized idle speed control stabilization of engine.

采用闭环调节点火提前角控制扭矩波动，实现了发动机的怠速最佳稳定控制。

the rules for the fixed engine speed with constant engine speed between torque transfer of the clutch and throttle angle were established.

归纳车辆起步时离合器传递转矩和节气门开度的变化规律，实现发动机恒转速起步。

a fixed angle constant velocity torque transfer device, comprising.

一个固定的角度恒定速度扭矩传输设备，其中包括。

It's the cardan joint that transfers the torque in a changeable angle.

万向节能够实现可变角度的扭矩传递.

Compared the two angular velocity, the initial angle of90 °, the flexor peak torque is decreasing, but the biceps femoris and gastrocnemius are in better discharge status.

两种角速度下，在起始角90。时，虽屈肌峰力矩有所降低，但股二头肌和腓肠肌均处于较佳的放电状态。

And the function relation is established between turn-off angle and rotor speed in order to reduce the torque and increase the torque.

以降低转矩脉动，提高平均转矩为目标，建立了最优关断角与转速之间的函数关系；

The side slip angle, cornering force, aligning torque and cornering potential energy of the pneumatic tires were deduced. And the spring deformation energy and damping-force potential energy of the wheel-rail radial contact were also deduced. 4.

推导了充气轮胎的侧偏角、侧偏力、回正力矩和侧偏势能，也推导出了承重轮、导向轮的轮轨接触弹簧变形能和粘性阻尼力势能。

In chapter 3, the control object of this subject, which is a three-link gymnastic robot on horizontal bar with limited joint torque and joint angle is brought forward and its mathematic model is developed.

第三章，提出本课题研究的对象：关节力矩和旋转角度受限的三连杆单杠体操机器人，推导了它的数学模型；