voltage reference的例句大全

Resistors require a reference voltage to work.

电阻器需要一千工作参考电压.

Reference source method is adopted to overcome the wiring shortcoming in traditional voltage sampling method.

系统采用基准源法的布线结构,以克服传统电压取样法中布线复杂的缺点.

This paper introduces a supply voltage band-gap reference circuit which used a self-bias cascode current mirror.

因此介绍了一种采用自偏置低压共源共栅电流源的带隙基准电路结构,用两个电阻代替了偏置电路.

It compensates for the temperature characteristics of the resistor and the threshold voltage VTH in such a way that the reference current has small temperature dependence.

主要利用电阻的温度系数与阈值电压VTH温度系数相同的特性实现温度补偿原理。

An ultra-low voltage, low power current reference was presented based on zero temperature coefficient ( ZTC) bias point and temperature compensation.

利用零温度系数偏置点技术和温度补偿技术设计了一个超低压、低功耗的电流基准源。

A new space vector modulation method based on reference voltage decomposition for multilevel VSI

基于参考电压分解的新型多电平逆变器空间矢量调制方法

The design of a linear temperature compensation voltage bandgap reference is based on the traditional bandgap.

基准电压源根据传统带隙基准温度补偿原理，设计了一级温度补偿的片上带隙基准源。

The outer layer computes the reference and keeps the capacitance voltage invariableness.

外层控制实现参考值的计算和直流电容电压控制。

its applicability of multi-object and the handling of internal voltage control technology have a good reference value on similar projects.

其多对象的适用性及内部电压的处理技术对类似控制工程有很好的参考价值。

Study and Design of Reference Voltage Generator with Adjustable Temperature Coefficient

温度系数可调的基准电压产生电路研究与设计

Based on bulk-driven and resistive subdivision techniques, an ultra-low voltage CMOS bandgap reference using second-order temperature and current feedback techniques is realized.

采用二阶温度补偿和电流反馈技术，设计实现了一种基于衬底驱动技术和电阻分压技术的超低压CMOS带隙基准电压源。

Therefore generator terminal voltage vector is selected as quasi-synchronous reference axis relative to rotor, and the generator model in two reference frames is established.

故选择机端电压矢量作为转子准同步参考轴，建立了基于单机二系坐标的发电机模型。

The tertiary voltage control module gives the reference voltage curves of the pilot nodes by a power loss least based optimal power flow ( OPF) calculation.

三级电压控制利用以网损最小为目标的最优潮流计算，求出中枢母线电压的设定值曲线。

This paper treats of frequency stability of conventional 12-channel carrier transmitters as used in collieries, with particular reference to the considerable variations of underground transmission line impedance and fluctuations of supply voltage.

本文根据煤矿井下载波传输线路阻抗变化大、电源电压波动大的特点，针对传统的矿用十二路载波发射机，讨论了其振荡频率（即发射频率）的稳定性问题。

A real-time current detection based on FBD ( Fryze-Buchholz-Dpenbrock) method is pre-sented to detect the harmonic, negative-sequent and zero-sequent currents in three-phase four-wire system, and the essential of the method is the projection transformation of reference voltage.

为了快速、有效地检测出三相四线制电力系统中的谐波、负序和零序电流，提出了一种基于FBD法的电流实时检测方法。

Then a reference thermal image whose impact of transmission attenuation and load voltage can be neglected will be selected from the thermal images collected.

然后，从拍摄的多幅热像中，选取一幅传输衰减和负荷状态影响可以忽略的热像作为参考。

To meet the requirements of the accuracy of the bandgap reference, the thermal voltage is used on a transistor with negative feedback resistor to generate a compensation current for high-order compensation.

为了满足控制系统对基准的精度的要求，借鉴分段补偿的思想，利用热电压在一带负反馈电阻的三极管上产生补偿电流，对基准进行了高阶补偿，使得温漂更低。

Such as: band gap reference voltage, the bias circuit, error amplifier, oscillator, PWM comparator, over thermal protection, under voltage protection, logic control part.

其中包括：带隙基准源、偏置电路、误差放大器、振荡器、PWM比较器、过温和欠压保护电路、逻辑控制等部分。

The reference voltage supplied to the AD7760 determines the analog input range.

模拟输入范围取决于AD7760采用的基准电压。

In order to reduce the DAC output voltage on the comparator input range requirements, bold use of capacitive pressure relief technique and ultimately to achieve the reference voltage to supply voltage.

为了降低DAC的输出电压对比较器输入范围的要求，大胆地采用电容缓压技术，最终可实现参考电压达到电源电压。