wear process的例句大全

surface plastic deformation always occurs during the whole tool wear process. the drastic wear of the flank surface on cutting tool produces white layer in workpiece surface.

工件表面的塑性变形在刀具磨损整个过程中都会发生，加工表面白层在刀具后刀面磨损剧烈时产生，但X射线分析没有发现相变。

Measurement and Analysis of the Energy Consumed in Gouging Abrasive Wear Process

凿削磨损过程中能耗的测定与分析

The wear mechanism of original WC-Ni cemented carbide during the wear process is abrasive wear with the main characteristics of plastic deformation of Ni binder phase and fall-out of WC grains, and wear resistance depends on the hardness of cemented carbide.

原始WC-Ni硬质合金的磨损以Ni粘结相的塑性变形和WC晶粒脱落为主要特征的磨粒磨损，耐磨性依赖于硬质合金的硬度。

The evolutions of wear debris characteristics as wear progress in sliding wear process was studied.

为提高基于磨粒的机器状态监测的准确性,研究了磨粒特征随滑动磨损进程的变化规律.

Based on the basis of fuzzy conditional probability the fuzzy reliability of every different state was found thus depicted more deeply the essence of tear and wear process.

在基于模糊条件概率的基础上，求出各个差异状态的模糊可靠度，从而更深入地刻画了磨损过程的实质。

Dynamical Measuring and Analysis of the Single Abrasive Particle Gouging Wear Process

单颗粒凿削磨损过程的动态测量与分析

the wear process can be divided as running-in and stable wearing period.

涂层的磨损过程可分为磨合期与稳定期。

The wear process of tribology system in general meaning has been analyzed and discussed.

研究油液分析故障诊断理论和方法的目的在于油液分析数据作出高水平的判断.

Study on Quality Control Chart of Tool Wear Process

刀具磨损过程的质量控制图

The graphite particles size distribution during wear process were acquired through Scanning Electronic Microscope ( SEM) imaging and the particle size analyzing by the software.

同时借助扫描电子显微镜和粒度分析软件，对磨损过程中产生的石墨磨屑进行了粒度分析，给出了不同条件下石墨磨屑尺寸的频率密度分布；

Wear Process and Its Simulation Test of Friction Pair of High Pressure Pump in Antiwear Hydraulic Oil Test

抗磨液压油试验高压泵摩擦副磨损过程分析及其模拟

In regard to non wear resistance of the white iron shot in the practical application process, alloy iron shot have been produced by means of adding alloying element and proper heat treatment.

针对白口铁丸在实际应用过程中不耐磨易破碎的现象，在白口铸铁中通过添加合金元素及适当热处理等手段生产合金铁丸。

the rotor is a steel screw whose outer surfaces are coated with wear-resistant materials, and its level of manufacturing process is already very high. the traditional stator is a thin-walled steel pipe, and its inner surface cohere with the inner helical surface rubber bush.

转子是一根外层表面镀有耐磨材料的钢制外螺旋曲面螺杆，其制造工艺水平已经很高；传统的定子是内壁粘着有内螺旋曲面橡胶衬套的薄壁钢管。

Result shows that with high velocity and light loads, the frictional and wear mechanism is slight abrasion wear due to the generation of dispersion strengthened intermediate harden phase and solid lubricative oxide during the process of friction.

在高速轻载时，Ni-Fe-W合金镀层在摩擦过程中会生成有弥散强化作用的中间硬质相和起固体润滑作用的氧化物，使其磨损表现为轻微的磨粒磨损。

Fretting wear is a surface degradation process invariably observed when two contacting bodies are subjected to small amplitude oscillatory movements, which has been one of main causes leading to tight fit assembly failures in aeronautical application, nuclear powder, railway industries and so on.

微动磨损是一种表面破坏过程，在小位移幅值（微米量级）震动的两接触表面几乎都可以观察到；已成为核电、航空、铁路等工业领域中紧配合部件失效的主要原因之一。

Adjusting fiber tension by means of exerting static-friction indirectly in FW process according to certain predetermined curve of tension change ( namely, FW tension rule), the system can control high tension of winding fiber precisely with little wear and tear to fibers.

通过静摩擦力间接施力方式按照设定张力变化曲线施加和调整缠绕过程的张力，实现了对纤维低磨损下的大张力高精度控制。

The short answer as to why so many characters wear gloves is that animation is an intensive process.

关于为什么这么多角色戴手套的简短回答是动画是一个密集的过程。

The results show that it can obviously promote the ion nitriding rate and enhance the wear resistance of crankshaft through putting the rare earth element as La and Ce into nitriding furnace or passing over some CO_2 during ion nitriding process.

试验表明，在渗氮炉中放入含La、Ce的混合稀土，或在离子渗氮过程中通入少量CO2气体，都能明显促进离子渗氮，提高曲轴的耐磨性。

Conventional heat treatment of low alloy martensitic wear-resistant steel is quenching and low-temperature tempering process, from which it can get tempered martensite structure which has a good combination of strength and toughness.

低合金马氏体耐磨钢的传统热处理工艺为淬火后低温回火，得到回火马氏体组织，具有良好的强度、硬度和韧性的配合。

Experimental Study on Straw Cutting Process and Wear Resistance and Strength Toughness of Cutters; So improvements of the obdurability of the tool tips and cutting edges are very important to better the cutting property of the end mill.

秸秆切割破碎与揉切机刀片耐用性试验研究刀尖是刀具中最薄弱的环节，提高刀尖及切削刃的强韧性对改善刀具切削性能尤其重要。