wear process

The wear process of tribology system in general meaning has been analyzed and discussed.

研究油液分析故障诊断理论和方法的目的在于油液分析数据作出高水平的判断.

Numerical Analysis for Influences of Running in Process on the Lubrication Properties& Wear of Asperity and Profile

磨合过程对润滑性能影响的数值分析&粗糙峰与轮廓的磨损

First, the theory of fretting wear and studies on fretting fatigue were introduced and the parametric method was used in the process of creating the model of dovetail joints in UG software.

本文介绍了微动损伤的机理和微动疲劳寿命的研究方法；利用UG软件对燕尾榫联接结构创建了参数化实体模型；

The evolutions of wear debris characteristics as wear progress in sliding wear process was studied.

为提高基于磨粒的机器状态监测的准确性,研究了磨粒特征随滑动磨损进程的变化规律.

Dynamical Measuring and Analysis of the Single Abrasive Particle Gouging Wear Process

单颗粒凿削磨损过程的动态测量与分析

Wear Process and Its Simulation Test of Friction Pair of High Pressure Pump in Antiwear Hydraulic Oil Test

抗磨液压油试验高压泵摩擦副磨损过程分析及其模拟

Study on Quality Control Chart of Tool Wear Process

刀具磨损过程的质量控制图

Adjusting fiber tension by means of exerting static-friction indirectly in FW process according to certain predetermined curve of tension change ( namely, FW tension rule), the system can control high tension of winding fiber precisely with little wear and tear to fibers.

通过静摩擦力间接施力方式按照设定张力变化曲线施加和调整缠绕过程的张力，实现了对纤维低磨损下的大张力高精度控制。

By adopting the m phased fuzzy statistics and choosing m typed state of reliability this paper carried out straggly a description upon the dynamic process of tear and wear.

本文采用m相模糊统计取m种可靠性状态离散地进行描述磨损的动态过程。

Based on the basis of fuzzy conditional probability the fuzzy reliability of every different state was found thus depicted more deeply the essence of tear and wear process.

在基于模糊条件概率的基础上，求出各个差异状态的模糊可靠度，从而更深入地刻画了磨损过程的实质。

The wear mechanism of original WC-Ni cemented carbide during the wear process is abrasive wear with the main characteristics of plastic deformation of Ni binder phase and fall-out of WC grains, and wear resistance depends on the hardness of cemented carbide.

原始WC-Ni硬质合金的磨损以Ni粘结相的塑性变形和WC晶粒脱落为主要特征的磨粒磨损，耐磨性依赖于硬质合金的硬度。

Mechanism and affecting factors of casing wear during the process of testing

石油井下套管磨损机理与影响因素分析

The graphite particles size distribution during wear process were acquired through Scanning Electronic Microscope ( SEM) imaging and the particle size analyzing by the software.

同时借助扫描电子显微镜和粒度分析软件，对磨损过程中产生的石墨磨屑进行了粒度分析，给出了不同条件下石墨磨屑尺寸的频率密度分布；

Conventional heat treatment of low alloy martensitic wear-resistant steel is quenching and low-temperature tempering process, from which it can get tempered martensite structure which has a good combination of strength and toughness.

低合金马氏体耐磨钢的传统热处理工艺为淬火后低温回火，得到回火马氏体组织，具有良好的强度、硬度和韧性的配合。

Measurement and Analysis of the Energy Consumed in Gouging Abrasive Wear Process

凿削磨损过程中能耗的测定与分析