working temperature的例句大全

According to the structure and working principle of the urination assist system, the simulated experimental system is built which include urinary simulated unit, driving unit, measurement and control unit, environmental temperature control unit and computer. 4.

根据排尿助力系统的结构及工作原理，设计搭建了一台由泌尿模拟单元、驱动单元、测控单元、环境温度控制单元和计算机组成的模拟实验系统。

The numerical analysis shows that the temperature field of the radiator gets uniform apparently when the working fluid flows.

结果表明：辐射器内工质的流动对辐射器的温度分布有明显的改善作用；

The temperature of supporting combustion air will rise to 600 C when the self-preheating process of hot blast stove is adopted, so the working condition of ceramic burner will be worse and the pulsating combustion will be caused easily.

热风炉采用自身预热技术后，由于空气预热温度升高，使陶瓷燃烧器工作条件恶化，易产生脉动燃烧。

The working principle and energy conservation of pin, screw and temperature control equipment in pin barrel cold feed extruder were described.

介绍了销钉机筒冷喂料挤出机中销钉、螺杆及其新型温控装置的工作原理，论述了上述元件节能的理论依据。

After three heating forms of theoretical cycle were compared, in accordance with the working specialities of internal combustion engines, it was confirmed that performance of the constant pressure heating cycle is optimal within temperature and pressure restraints.

基于内燃机的工作特点，比较理论循环的三种加热方式，证明了温压约束下等压加热循环性能最优。

The martensitic transformation temperature and e/ a increase with the Ar working pressure increasing, the martensitic phase with tetragonal structure can be obtained at room temperature.

随Ar工作压强的升高，薄膜的e/a值逐渐增大，薄膜的相变温度逐渐升高，室温下可以获得具有四方结构马氏体相的Ni-Mn-Ga薄膜。

Calculation on the Insulating Thickness of Thermal Network Pipes Varying with Temperature of Working Pair and Thermal Conductivity of Insulating Material

热网管道的保温厚度与工质温度、保温材料导热系数的关系计算

The results of analysis on the hot working longitudinal cracks and study on the thermal plasticity of stainless steel SUS 416 show that there is a low plasticity region in the temperature range 900 ℃ to 1000 ℃ for steel billets.

对SUS416不锈钢的热加工纵向裂纹和钢坯横向、纵向的热塑性研究结果表明；钢坯的横向热塑性在900～1000℃温度区间存在一明显的低塑性区。

According to heat loss of thermal network pipes per meter stated by nation, thickness of thermal insulating layer varying with thermal conductivity of insulating material and temperature of working pair is studied by numerical calculation.

在国家规定的热网管道的每米热损失下，其保温层厚度随着保温材料的导热系数及工质温度的不同而不同。

Thermal Deviation of water wall outlet piping caused by bad furnace firing condition can cause considerable temperature difference on the working media of inlet piping which is introduced to furnace roof inlet header.

由于炉膛燃烧不理想导致水冷壁出口管的热偏差，使进入顶棚进口集箱的引入管的工质产生了较大的温差。

Finally, the steady tire temperature field and rolling resistance under different working conditions are calculated based on the direct solving strategy.

基于直接策略，分析计算了不同工况下的轮胎稳态温度场和滚动阻力。

But its number had reached the order of magnitude of 10-4, the electrolyte working at the temperature of 600 ℃ could be used in the preparation of sensors.

但是电导率数值达到10-4数量级，所以600℃环境温度下工作的固体电解质可用于制备传感器。

The temperature at the cryoprobe tip increased quickly when the working gas was shifted to He.

当工质由氩切换为氦后，刀头温度迅速上升，冰球随即熔化；

It was shown that the temperature rise can be of great value under normal working conditions and higher slip ratio.

结果表明，在正常接触工况和较大滑滚比条件下，轮轨接触温升可达到可观数值。

This is because at the end of the process, the adsorption bed temperature is closed to heat source temperature. When it is suddenly switched to the working condition, absorbent temperature only can reduce down slowly after the bed temperature decreases.

这是因为脱附过程结束时，吸附床温度接近热源温度，突然切换到吸附工况，吸附剂温度只有在床体温度降低后缓慢降低。

when the buried transmission piping is built, the major temperature difference of piping when being placed and when working makes it necessary to lay a fixed anchorage so as to limit the expanding displacement.

铺设埋地热输管线时，由于管子下沟回填和工作时存在较大温差，所以需要设置固定墩限制管道的热膨胀位移。

This paper introduced a kind of working principle of multi channel temperature controlled equipment to control the temperature of compression moulding die by the use of high temperature heat conducting oil as well as the design of its high temperature compound stop valve and regulating valve.

本文介绍了一种利用高温导热油来控制压铸模模温的多通道温控机的工作原理及其高温组合截止阀和调节阀的设计。

The contrasting results show that sound intensity, radiation time and frequency are the main factors, and the secondary factors are test temperature, working mode and settlement time.

对比实验研究表明：声强、辐照时间和频率是影响破乳脱水率的主要因素，而实验温度、工作方式、沉降时间等为次要因素。

Impacts on the throughflow matching, surface metal temperature of the first grade static blade, and also the average working lifetime of the high-temperature blade when the gas turbine is used for coal fuel gas is applied are analyzed.

分析了改烧中低热值煤制燃料气，对燃气轮机通流匹配、一级静叶金属温度以及高温叶片平均寿命的影响。

By the test of engine platform, the mathematic models on temperature contrast loading based on the loading of three-way catalyst and the warming up characteristics of speed temperature, can be used for supervision of working efficiency of three-way catalyst.

通过发动机台架试验，在研究三元催化转换器负荷和速度升温特性的基础上建立的温差负荷数学模型，可用于监控三元催化转化器的工作效率。