zero error的例句大全

A compensation technique for piezoresistive accelerometer's zero error, temperature excursion, dynamic property is worked out in this paper. We give the theory and achieve method of compensation.

对扩散硅压阻式加速度传感器的零点误差、温度漂移和动态特性等进行了分析研究，给出了它们的补偿原理及其实现方法。

it gives us the simulation curves together and respectively caused by initialization errors, zero error of accelerometer and invariable gyro drift, and then it analyzes the simulation results.

文中对初始值误差、加速度计零位误差及陀螺常值漂移共同作用及各自分别作用条件下进行了仿真，通过仿真曲线对各误差源进行了简要地分析。

Experiments show that zero error and linear system error exist when SAI is tested by the four-wheel aligners.

试验表明：四轮定位仪测量主销内倾存在零点误差和线性度系统误差。

The result of test showed in the same instruction time, neural network fuzzy controller could achieve zero error measurement about angle instruction, and neural network fuzzy controller remarkably minish overtop value compared with the general PID controller.

结果证明，在同一指令时间内，模糊神经网络控制器能够很好地完成角度指令的零误差调节，与常规PID控制器相比较，模糊神经网络控制器的超调量显著减小。

Zero error decrypted speech ensures the high quality of speech.

解密的零误差，保证了良好的语音质量。

Code with a divide-by zero error fails only if you divide by zero.

只有在被零除的时候,代码才会发生被零除的错误.

Let's look at a division by zero error.

下面让我们来看一下division by zero这个错误。

How the Enterprise Owner and Professional Manager to Break Away from the Error Areas of the Zero-sum Game

企业所有者与职业经理人如何走出零和博弈的误区

The IRR can be found by trial and error by using a number of discount factors until the NPV equals zero.

内含报酬率可以采用验误法用一系列的折现数计算。

The maximum likelihood criterion is equivalent to the minimum root-mean-square error criterion when the supposed noise is Gaussian white noise of average value of zero.

当假设干扰是均值为零的高斯白噪音时，最大似然准则等效于最小均方误差准则，求取地震子波的最大似然估计值就是求解一个托布里兹方程组。

This paper introduces a few key problems in the process of temperature examination in computer temperature control system, including choice of temperature sensor, A/ D convert and zero adjust, scale transformation error compensation, and the design method of temperature examination.

本文介绍微型计算机温度控制系统中温度检测过程的几个关键问题，包括温度传感器的选择、A/D转换与零点迁移、标度变换与误差补偿，以及温度检测环节的设计方法。

Zero Phase Error Tracking Controller ( ZPETC ) was used to partially solve the problem.

零相位误差跟踪控制器 ( ZPETC ) 的提出部分地解决了这一问题.

Aiming at CDMA communication system, spreading sequence has perfect correlation properties only within the bound of synchronized error, Low/ Zero correlation zone ( LCZ/ ZCZ) was proposed.

针对准同步CDMA通信系统，只要求扩频序列在同步误差范围内（一个或几个码片周期）具有和接近理想相关特性，提出了低/零相关区。

When measuring the surface of workpiece, the piezoelectric actuator drive focusing lens to move vertically to ensure that the focus is always on the surface of workpiece in every sample interval, and the focused signal error return to zero.

在测量工件表面形貌时.压电陶瓷驱动器驱动聚焦物镜进行垂直位移.从而确保在每一个采样间隔中焦点总是落在工件表面上，同时使得聚焦误差信号回零。

Set up the zero bias error compensation model of gyroscope at different temperature change condition respectively.

建立了硅微陀螺在不同温度变化条件下的零偏误差补偿模型。

The slope standard error and correlation coefficient of zero-crossing linear fitting

过原点直线拟合的斜率标准差与相关系数

Two different conditions and solutions of whether the intercept is zero or not in linear fitting are analyzed, the relationship between two correlation coefficient equations is discussed, the approximate calculative equation of slope standard error correlation coefficient when the intercept is zero is presented.

分析了直线拟合中截距是否为零的两种不同条件与解法，讨论了两种相关系数表达式之间的关系，给出了截距为零时斜率标准差与相关系数的近似计算式。

The result shows that the groove depth and duty cycle error of phase mask must be controlled within the range of| Δ h| < 38nm and| Δ f| < 0.11 respectively in order to make the zero order diffraction efficiency less than 5%.

分析表明，为使零级衍射效率小于5%，相位掩模的刻槽深度和占空比制作误差必须控制在｜Δh｜＜38nm和｜Δf｜＜0.11的范围内。

This paper analyses the impact of the magnitude, phase and installation position tolerances on sidelobe of shaped-beam pattern using a normal distribution with zero mean as error mode.

文中以均值为零的正态分布作为误差模型，分别就幅度、相位以及安装位置公差对赋形方向图副瓣带来的影响进行了统计分析。

Based on this identified model, zero phase error tracing controller ( ZPETC) is designed. Closed-loop band width is increased to 100 rad/ s or so.

基于闭环系统辨识模型设计了零相位误差前馈控制器（ZPETC），ZPETC将闭环系统带宽拓宽为100rad/s左右。