zero error

Experiments show that zero error and linear system error exist when SAI is tested by the four-wheel aligners.

试验表明：四轮定位仪测量主销内倾存在零点误差和线性度系统误差。

This paper introduces a few key problems in the process of temperature examination in computer temperature control system, including choice of temperature sensor, A/ D convert and zero adjust, scale transformation error compensation, and the design method of temperature examination.

本文介绍微型计算机温度控制系统中温度检测过程的几个关键问题，包括温度传感器的选择、A/D转换与零点迁移、标度变换与误差补偿，以及温度检测环节的设计方法。

Zero error decrypted speech ensures the high quality of speech.

解密的零误差，保证了良好的语音质量。

This function returns 0 zero if no error has occurred.

如果未出现错误,那么将返回0.

A compensation technique for piezoresistive accelerometer's zero error, temperature excursion, dynamic property is worked out in this paper. We give the theory and achieve method of compensation.

对扩散硅压阻式加速度传感器的零点误差、温度漂移和动态特性等进行了分析研究，给出了它们的补偿原理及其实现方法。

Based on this identified model, zero phase error tracing controller ( ZPETC) is designed. Closed-loop band width is increased to 100 rad/ s or so.

基于闭环系统辨识模型设计了零相位误差前馈控制器（ZPETC），ZPETC将闭环系统带宽拓宽为100rad/s左右。

The result of test showed in the same instruction time, neural network fuzzy controller could achieve zero error measurement about angle instruction, and neural network fuzzy controller remarkably minish overtop value compared with the general PID controller.

结果证明，在同一指令时间内，模糊神经网络控制器能够很好地完成角度指令的零误差调节，与常规PID控制器相比较，模糊神经网络控制器的超调量显著减小。

Code with a divide-by zero error fails only if you divide by zero.

只有在被零除的时候,代码才会发生被零除的错误.

Let's look at a division by zero error.

下面让我们来看一下division by zero这个错误。

Besides standardization, zero correction error constitutes the most common error source of a gravimeter.

零位校正误差是重力仪除标定以外最主要的误差来源。

The result shows that the groove depth and duty cycle error of phase mask must be controlled within the range of| Δ h| < 38nm and| Δ f| < 0.11 respectively in order to make the zero order diffraction efficiency less than 5%.

分析表明，为使零级衍射效率小于5%，相位掩模的刻槽深度和占空比制作误差必须控制在｜Δh｜＜38nm和｜Δf｜＜0.11的范围内。

This paper analyses the impact of the magnitude, phase and installation position tolerances on sidelobe of shaped-beam pattern using a normal distribution with zero mean as error mode.

文中以均值为零的正态分布作为误差模型，分别就幅度、相位以及安装位置公差对赋形方向图副瓣带来的影响进行了统计分析。

Unless otherwise specified, the functions return an integer error code; zero indicates success.

除非特别说明，函数均返回一个整型的错误码；如果是零就表示操作成功。

This paper presents a control mode of STATCOM, which has a fast dynamic response, zero static error, compensate unsymmetrical load.

提出了一种动态响应快，无静态误差，可用于补偿不对称负载的STATCOM的控制方法。