feed rate的例句大全

The spindle speed, feed rate, NC program, machine switch machine time information acquisition.

实现了对主轴转速，进给速度，NC程序，机床的开关机时间的信息的采集。

Besides, the product purity also can be raised through controlling the feed rate of the light-off tower, or adding nitrogen in the top of light-off tower.

此外，控制脱轻塔的进料量和在脱轻塔顶加入氮气进行吹扫也能解决产品质量不达标的问题。

The hardware and software structure of a CNC system for high feed rate punching ma-chine is introduced.

介绍了一种冲床高速送料数控系统的硬件和软件结构。

the opening of the multi-function unit can only be processed in the lowest feed rate. 5.

多功能单元启用只能在最低进料速度下加工。

A more prudent its size, the greater the feed rate, a stronger ability to eat thick, more continuity sewing speed.

其具有更稳重的体积、更大的送料幅度、更强劲的吃厚能力、更加连续性的缝纫速度。

Inverse time feed rate code

反比时间进给率代码

Based on the results, the process calculation of thin film evaporator was realized by synthetically considering the optimum feed rate derived from CFD simulation.

以此为基础，综合考虑CFD数值模拟得出的最佳进料量要求，实现薄膜蒸发器的工艺计算。

the effects of feed rate and split ratio ( overflow rate to feed rate ratio) on fractionation of pulp fiber are studied.

研究了进料量Qf和分流比R（溢流与进料之比）对筛分的影响。

A new system of rapid roll carriage infeed and return, together with automatic selection of pressure and feed rate, has improved the already impressive floor-to-floor times achieved.

快速辊子进给和返回系统和自动压力、进给速率调节器提高了工作效率。

The influences of grinding depth, feed rate and circular linear speed of the grinding wheel on the grinding forces and the forces on each diamond grit were obtained.

对不同粒度条件下磨削深度、进给速度和砂轮线速度对磨削力的影响进行了分析。

The influence of depth of grinding, feed rate and circular linear speed of the grinding wheel on the grinding forces with respect to the maximum chip thickness of a single active diamond was analyzed.

从单颗金刚石最大切削厚度的角度，分析了磨削深度、进给速度和砂轮线速度对磨削力的影响。

The process parameters, including depth of cut ( ap), feed rate ( vf) and circular linear speed of the sawblade ( v,), varied over a relatively wide range during the experiments, while the segment surface being kept at a relatively stable state.

实验过程中在保持金刚石节块表面状态基本不变的情况下，对锯切深度ap、叫进给速度Vf和锯片圆周线速度Vs进行了较大范围的变化。

The emulsifier content and feed rate affect latex swelling and shell polymerization by the making a change of latex number and total reaction rate coefficient respectively.

乳化剂量和加料速率分别通过影响胶粒数和总体反应速率系数而对胶粒溶胀和壳层聚合反应产生影响。

With the feed rate and cutting depth increases, surface roughness increases. The surface roughness first increases then decreases along with the increasing of corner radius.

表面粗糙度正交试验的结果表明：表面粗糙度随着切削速度的增大而减小，随着进给量和背吃刀量的增大而增大，随着刀尖圆弧半径的增大出现先减小后增大。

If we controlled the rotational speed and feed rate well of the homemade tubular reactor, product discharge was in good condition, and the yield was78%.

自制管式反应器控制转速和加料速度，产品出料情况良好，且收率达到74.5%。

A Portable Instrument for Measuring Wire Feed Rate

便携式送丝速度测量仪

Even the relative low wire feed rate of 6 m/ min exceeds 3 times of routine TIG welding, which greatly improves the welding efficiency.

6~10m/min的送丝速度较常规TIG焊接提高了3倍以上，大大提高了焊接效率。

Welding parameters such as angle of bending tip, pulse voltage, wire feed rate, pulse mode, size of groove and welding speed can affect the appearance of weld.

导电嘴弯曲角度、送丝速度、峰值电压、协同模式、焊接速度和坡口尺寸均会对窄间隙焊缝成形产生重要影响。

In this paper, the following is introduced, the setting for laser welding with filler wire, the interaction between laser beam and filler metal and weldment, the relations between wire feed rate and welding speed.

介绍了激光填丝焊的装置；论述了光束与焊丝和工件的相互作用及送丝速度与焊接速度之间的关系；

Research on Steady Feed Rate of SSV

逐点比较法进给速度的稳恒研究