load condition的例句大全

Numerical tests of initial condition characteristics of AR model in short-term load forecasting

短期负荷预报AR方法初值性质的数值测试

In this paper, the principle and method for the test on switching figure of on-load tap changer ( OLTC) are introduced. On the basis of analyzing the problems in field, the methods for estimating the condition of OLTC are presented.

介绍了有载分接开关切换波形测试的意义、原理和方法，指出现场测试经常遇到的问题并分析了其原因，提出了根据现场所测波形判断有载分接开关能否正确切换的方法。

Based on the aging loss calculation, the limited value of temperature rise for F class insulation transformer on rated operating condition is derived. This value is satisfied with the desire of standard load system of duty class ⅴ and ⅵ.

通过寿命损耗计算，得出了F级绝缘变压器在Ⅴ级和Ⅵ级负载标准工作制条件下额定运行的温升限值。

Under the immovable operating condition, this paper calculated the thermal load of heat pump drier, determined configuration of device and relevant size, and analyzed the functions of the device.

在定工况条件下对热泵干燥装置负荷进行计算，确定了系统设备的配置和相应的选型，分析了装置可实现的功能。

Experimental Investigation on Thermal Load in Cylinder Head Fire-face of Air-Cooled IC Engines under Transient Condition

风冷内燃机缸盖火力面过渡工况下热负荷试验研究

Through study, this paper elaborates a new method to test RC beam health condition with attached load method.

提出了附加荷载动态测试钢筋混凝土梁健康状况新方法。

According to actual condition, seismic load of the coupled model is inputted from the bottom of reactor building.

耦联模型的地震载荷按照实际情况，由土建结构的底部输入。

Health condition and load carrying capacity evaluation of RC beam based on dynamic testing

RC桥梁健康状况及承载能力的动力评估试验

The design method of the high voltage and the fast response time pulse transformer used in the condition of low load impedance was introduced.

介绍了工作于低阻抗负载下的高压大电流快响应脉冲变压器的一种设计方法。

The condition of soft switch in all range of different static load is illustrated by the simulation method.

通过仿真，研究了在不同静态负载下实现全程软开关的条件。

Based on terminal conditions of numeric analysis, numeric analysis of the relative expanding difference of shaft and cylinder of steam turbine was made at the different temperatures in the no-load work condition by ANSYS.

利用数值分析的边界条件，运用ANSYS有限元分析软件，对汽轮机转子及汽缸空负荷工况下，不同排气温度时的相对胀差进行了数值模拟。

The paper briefly introduces the natural condition, design load and structural type of sunan Heavy Cargo Wharf.

简要介绍苏南重件码头的自然条件、设计荷载及结构型式。

Composites; Bonded-bolted hybrid joints; Fabrication technical process; Load transfer mechanism; Bonded-bolted deformation harmony condition; Carrying capacity;

复合材料；胶螺混合连接接头；制作工艺；传力机理；胶螺变形协调条件；承载力；

As an example, the oil film pressure, the elastic deformation and the static performance of a tilting-pad thrust bearing in heavy-loading condition are calculated by using the out-domain method.

作为算例，用域外法联立求解雷诺方程和弹性变形方程，计算了大型可倾瓦推力轴承的油膜压力、弹性变形和相应的静特性参数。

A three dimensional finite element analysis on the structure of 4 tilting pad bridge bearing load cell in large turbine generator sets has been made. The influence of boundary condition on the stress or strain field of sensor is studied.

对大型汽轮发电机组四可倾瓦轴承双剪桥式负荷传感器结构进行了三维有限元分析，研究了不同边界条件对传感器结构应力（应变）场的影响。

The author analyzes the stress in hoisting rope taking it as a viscoelastic body under the condition of application of dynamic tension load, and discusses the strength in the rope in consideration of dynamic load and bending stress.

把矿井提升钢丝绳作为粘弹性体，分析了拉伸动负荷作用下提升钢丝绳的应力，并考虑动负荷及弯曲应力讨论了提升钢丝绳的强度。

Effect of simple loading condition on relation between load and displacement of cracked specimen

简单加载条件对裂纹试样载荷&位移关系的影响

The nonlinear analysis of the standard cold insulation box of fractionating tower in industrial use was presented and the calculating model and analytic method were deduced under the load of inner-filling in the condition of having and not having lateral-displacement.

对工业应用中定型化的分馏塔保冷箱进行了非线形分析，推导了无侧移情况下和有侧移情况下内填料作用的计算模式及分析方法。

On Efficiency Property of Throttle Speed Control Circuit in Condition of Constant-Load

恒负载工况下节流阀调速回路效率特性研究

The results indicate that the influence of load types, chord boundary conditions, load sequences and axial tension on chord can be ignored, but the boundary condition of branch pipe and the axial compression on chord may affect the bearing capacity of the joints.

结果表明，荷载类型、主管的边界条件、加载顺序、主管的轴向拉力对节点承载力的影响可以忽略，而支管的边界条件，主管的轴向压力对节点承载力会产生一定的影响。