maximum temperature的例句大全

TPD characterization of n-propylamine temperature programmed desorption indicated that the acid density and acid strength of the catalyst acid sites changed with the temperature rise of catalyst activation and reached a maximum at 250 ℃ and 350 ℃, respectively.

催化剂表面酸强度和酸密度均随着活化温度的提高先增大后降低，分别在350℃和250℃时达到极大值。

Forecast Method Research of Maximum and Minimum Temperature in Qinghai Province

青海省最高最低气温预报方法研究

An Diagnosis Analysis of Asymmetry Variations of Maximum and Minimum Temperature in Qinghai Province

青海省最高、最低气温不对称性变化的诊断分析

Also, we show that the power output has a maximun with respect to the fuel flow rate or any of the overall pressure drops and the maximized power output has additional maximum with respect to the overall pressure ration and overall temperature ratio.

分析表明，功率输出相对于燃料流率或任意一个压力损失有一个最大值，最大功率输出对总压比有附加最大值。

The results showed that water and acid wash can make TG and DTG curves of rice straw pyrolysis shift to higher temperature section, and the maximum weight loss rate and temperature increased.

试验结果表明：水洗及酸洗可使水稻秸秆的热解主反应区热重和微分热重曲线向高温侧移动，最大失重速率和最大失重温度升高；

Testing results given, the effect of the evil conditions is studied emphatically on the maximum combustion pressure, exhaust temperature and turbocharger surge.

文章给出了试验结果，并着重研究了它们对爆发压力、排气温度以及增压器喘振的影响。

At the primary stage of drying, the maximum value of elastic tension strain of the timber surface increased with drying temperature rising, and decreased with increment of equilibrium moisture content ( EMC).

干燥前期，木材表层伸张弹性应变最大值随着温度和平衡含水率的增加而减少，木材表层塑性应变则随平衡含水率的增加而增加。

Coil coatings was thermal analyzed and researched with DSC in order to test glass transition temperature ( Tg) of the paint film at the maximum precoated metal temperature ( PMT) and determine the optimal curing conditions of different coil coatings.

采用DSC进行卷材涂料热分析研究，测试在不同PMT（最高金属板温）下漆膜的Tg，以确定各种卷材涂料的最佳固化条件。

Taking 17 year old Ginkgo biloba as test material, the effects of temperature and precipitation on wood ring width, ring density maximum density and minimum density were studied.

以北京地区17年生银杏为试材，研究了气温和降水对银杏木材年轮宽度、年轮密度、最大密度、最小密度的影响。

The value of temperature change was calculated by Thermodynamic equation. The three films all appear the maximum heating temperature change near their curie points.

热力学公式计算铁电薄膜电热温变值，三种薄膜在各自的居里点附近均出现了最大电热温变值。

This standard describes the procedure for obtaining the Hydrostatic Design Stress ( maximum working strength) for any thermoplastic pipe material at any practical temperature.

这个标准描述了获得流体静力设计应力（最大工作强度）的步骤，用于任何实际温度下的任何热塑塑料管道材料。

Room temperature fracture toughness was measured by three-point bending test and the KQ value for the DS condition was much higher than that for the as-cast condition. The maximum fracture toughness was 19.7MPam~ ( 1/ 2).

三点弯曲试验表明，定向凝固后试样的室温断裂韧性也得到了明显的提高，K Q最高达到了19.7MPam~（1/2）。

Records the highest and lowest temperatures reached during a period of time. Hardness was decreased after maximum by high temperature heating.

记录在一定时期的最高温度和最低温度的温度计。高温加热硬度达最大硬度以后保温硬度降低。

With the increase of engine load, the igni-tion timing will advance, the maximum heat release rate and the maximum combustion temperature as well as the combustion duration will increase.

负荷增大时，双燃料发动机燃烧始点提前，最大燃烧放热率增高，最高燃烧温度升高，后燃较严重。

The flux keeps increasing until reaches 5 W/ m2. A maximum anomaly of 0.5 K is found in ground temperature. Correspondingly, there are positive anomalies of around 1 W/ m2 in surface sensible, latent and outgoing long-wave radiation fluxes.

积分3个月后，由地下进入地表的热流量增幅可达1W/m2以上，并持续增大到5W/m2，地表最大升温约0.5K，同时地表感热、蒸发潜热及长波辐射通量均有1W/m2左右的正异常；

The influence of the supporting beam depth, the thermal coefficient of the material and the heat exchange coefficient on the maximum principal tensile stress in the boiler-supporting beam under the load of the temperature field is analyzed as well.

同时分析了支撑梁在该温度场作用下支撑梁宽度、材料的导热系数、梁表面热交换系数对梁内最大主拉应力的影响。

The thermal decomposition curve of PP/ ATP composites showed that the initial temperature of thermal decomposition and the temperature of maximum thermo-gravimetric rate were all shifted towards high temperature.

从复合材料的热分解曲线可知复合材料的热分解初始温度向高温移动，最大热失重速率对应的温度也移向高温。

The heating rates shift the maximum thermal degradation rate and its corresponding temperature.

升温速率改变单体热解速率最大值和其对应的温度。

The results show that the thermal fatigue life decreases with enlarging the thermal cycle dwell time, the thermal cycle range and the maximum dwell temperature, and the minimum life is 879 cycle.

结果表明：随着热循环高低温停留时间、温度范围以及最高热循环温度的增大，热循环寿命减小，最小寿命为879周；

Great temperature gradient brought the thermal stress in un-reacted solid particles, and natural convection and thermal pulse in the melted aluminum. When the thermal stress was higher than its maximum strength of the reactant, the reactant would be broken and the reaction speed was increased.

大的温度梯度在未反应固体内部产生热应力，当该热应力大于当时固体反应剂的极限强度时，会导致未反应固体的破裂，由此加速反应进程；