maximum temperature的例句大全

The thermal decomposition curve of PP/ ATP composites showed that the initial temperature of thermal decomposition and the temperature of maximum thermo-gravimetric rate were all shifted towards high temperature.

从复合材料的热分解曲线可知复合材料的热分解初始温度向高温移动，最大热失重速率对应的温度也移向高温。

The final preferendum was about 30.54 ° C, critical temperature minimum was not higher than 45 ° C and critical temperature maximum not lower than 3 ° C.

鼎突多刺蚁的最终适温为30.54℃，临界低温不低于3℃，临界高温不高于45℃；

Critical deformation temperature, maximum deformation, deformation recovery temperature, deformation recovery time of NR/ LDPE materials are investigated in this paper.

研究了天然橡胶／低密度聚乙烯（NR／LDPE）材料的临界形变温度、最大形变量、形变回复温度、形变回复时间等形状记忆性能。

For methane/ ( water+ active carbon) system, methane gas storage capacity in hydrates was quite close to theoretical maximum value at the pressure range of 5.7~ 9.5 MPa and the temperature range of 275.8~ 280.0 K for some runs.

在甲烷/（水+活性炭）体系中，5.7～9.5MPa和275.8～280.0K时，一些水合物储气量的实验值已接近最大理论值，这是由于活性炭能为水和甲烷提供优异的接触条件。

At the test temperature, the maximum compressive strain, the maximum tensile strain and strain amplitude are all in exponential relationship with the axle load.

在试验温度下，最大压应变、最大拉应变和应变幅值均随轴载的增加呈指数关系增大。

The temperature and the maximum frozen depth of experimental road are measured to verify that the model reliable.

通过对试验路温度和最大冻深计算，验证了水热耦合模型的正确性。

With temperature decrease, maximum fibre elongation of cotton decreased and elongation period increased.

随温度降低纤维伸长最大值降低，伸长期延长；

The optimal mathematical models on the axial optimum temperature and maximum synthetic rate for a continuous heat exchange ammonia converter were established.

建立了连续换热式氨合成塔轴向最佳温度和最大合成率的优化模型，采用牛顿迭代法和龙格-库塔法对模型进行了数值解。

The flux keeps increasing until reaches 5 W/ m2. A maximum anomaly of 0.5 K is found in ground temperature. Correspondingly, there are positive anomalies of around 1 W/ m2 in surface sensible, latent and outgoing long-wave radiation fluxes.

积分3个月后，由地下进入地表的热流量增幅可达1W/m2以上，并持续增大到5W/m2，地表最大升温约0.5K，同时地表感热、蒸发潜热及长波辐射通量均有1W/m2左右的正异常；

With the increase of engine load, the igni-tion timing will advance, the maximum heat release rate and the maximum combustion temperature as well as the combustion duration will increase.

负荷增大时，双燃料发动机燃烧始点提前，最大燃烧放热率增高，最高燃烧温度升高，后燃较严重。

Set temperature control to maximum cooling.

将温度控制设置为最强制冷。

Records the highest and lowest temperatures reached during a period of time. Hardness was decreased after maximum by high temperature heating.

记录在一定时期的最高温度和最低温度的温度计。高温加热硬度达最大硬度以后保温硬度降低。

Water temperature model and maximum cooling capacity of a lake or pond

湖泊、池塘的水温模型与最大供冷能力的分析研究

The influence of the supporting beam depth, the thermal coefficient of the material and the heat exchange coefficient on the maximum principal tensile stress in the boiler-supporting beam under the load of the temperature field is analyzed as well.

同时分析了支撑梁在该温度场作用下支撑梁宽度、材料的导热系数、梁表面热交换系数对梁内最大主拉应力的影响。

The temperature for maximum internal friction lies between 200-300 ℃ with a frequency of vibration of about I cycle per second.

当振动频率约为每秒1周时，峰的巅值温度在200-300℃之间。

The heating rates shift the maximum thermal degradation rate and its corresponding temperature.

升温速率改变单体热解速率最大值和其对应的温度。

Room temperature fracture toughness was measured by three-point bending test and the KQ value for the DS condition was much higher than that for the as-cast condition. The maximum fracture toughness was 19.7MPam~ ( 1/ 2).

三点弯曲试验表明，定向凝固后试样的室温断裂韧性也得到了明显的提高，K Q最高达到了19.7MPam~（1/2）。

Great temperature gradient brought the thermal stress in un-reacted solid particles, and natural convection and thermal pulse in the melted aluminum. When the thermal stress was higher than its maximum strength of the reactant, the reactant would be broken and the reaction speed was increased.

大的温度梯度在未反应固体内部产生热应力，当该热应力大于当时固体反应剂的极限强度时，会导致未反应固体的破裂，由此加速反应进程；

Influence of Temperature Parameter on Maximum Unbalance Rate of Heating System

温度参数对供暖系统最大不平衡率的影响

Thermal sensitivity is a measurement on how easily fast chemical reaction will happen. The essence of studying thermal sensitivity of energetic materials is to find the relationship of time to maximum rate ( TMR) and the decomposition temperature.

热感度是物质在热作用下发生快速化学反应难易程度的度量，求取含能材料的热感度的本质是求取诱导期TMR与温度的关系。