sliding speed的例句大全

The effects of sliding speed and load were considered.

分别考察了滑动速度和载荷对两种材料的摩擦因数以及磨损量的影响。

The wear characteristics of polytetrafluoroethylene ( PTFE) were tested on the model MPX-200 pin-on-disk tester in this paper. The effects of sliding speed, load, temperature and surface roughness of counterparts on wear were determined.

作者用MPX-200型栓-盘摩擦磨损试验机测试了模压聚四氟乙烯的磨损性能，考察了滑动速度、负菏、温度及偶件表面粗糙度对磨损的影响。

The plastic deformation is accelerated at high sliding speed and normal load, which is accompanied by localized melting on the worn surfaces of the frictional materials.

在高速和高压条件下塑性变形加剧，摩擦材料磨损表面可见熔融迹象；

The results show that at low sliding speed and small load, the main dry sliding wear mechanism of the coating is oxidation wear, and the wear resistance of the coating is 2~ 4 times higher than that of tempered 45 steel.

结果表明，轻载低速条件下，熔涂层的干摩擦滑动磨损机制以氧化磨损为主，与淬火低温回火态45钢相比，熔涂层的耐磨性是45钢的2～4倍；

This indicates that as the sliding speed increases the effects of water lubrication and load carrying capacity of the friction pair are improved.

说明滑行速度提高时，水润滑效果会更加明显，且摩擦副具有较高的承载能力。

The results show that the wear rates of the two materials increase and the friction coefficients decrease with increasing of normal load and sliding speed.

结果表明，两种材料的磨损速度随载荷、滑动速度增大而增大，磨擦系数随之降低。

The influences of film thickness, normal load, and sliding speed on the friction and wear behaviors of PNMP films are investigated.

研究考察了薄膜厚度、法向负荷以及相对滑动速度对PNMP薄膜的摩擦和磨损性能的影响。

At the sliding speed of 2m/ sec under dry condition the wear rates of all the composites tested were lower than the matrix.

滑动线速度最高达9.4米/秒。在2米/秒干摩擦时，所有测试的复合材料磨损量均小于基体合金。

The wear resistance was compared through the weight loss curves of discs under constant load and sliding speed, and the wear transition diagrams of load versus sliding speed. Some new phenomena were discovered in these experiments.

耐磨性通过圆盘在恒载恒速下的磨损失重及载荷相对滑动速度的磨损机制转变图进行比较，试验中发现了一些新的现象。

on rational sliding speed of juvenile girls shot putters

论青少年女子铅球运动员的合理滑步速度

The experimental results indicate that with increasing of contact pressure the rate of wear of materials increases and with increasing of sliding speed the rate decreases.

结果表明，随接触压力的增加，材料的磨损率增加；随摩擦速度的增加，材料的磨损率减小。

The effect of surface phase constitution, surface roughness, sliding speed, press force and anti-rust oil on friction coefficient of galvannealed IF sheet steel has been tested and researched.

采用平板滑动实验研究了表面相组成、表面粗糙度、拉速、压力及涂油品种等因素对汽车用合金化热镀锌IF钢表面摩擦系数的影响。

Wear rate of Si_3N_4 ceramic rose with the increase of loads between Si_3N_4 ceramic and chilled iron while the effect of relative sliding speed on wear rate of Si_3N_4 ceramic is not as significant as that of load.

Si3N4陶瓷的磨损率随载荷的增大而增大，滑动速度对磨损率的影响要小于载荷对其的影响；

Traction characteristics of synthetic lubricants at high sliding speed contacts

大滑速下合成润滑油的摩擦牵引力研究

An Experimental Study of the Relation between Friction Force and Relative Sliding Speed

摩擦力-相对滑动速度关系的实验研究

Influence of Sliding Speed on Wear Resistance of Nano-Particles Composite Coating

滑动速度对纳米颗粒复合镀层摩擦性能的影响

Higher sliding speed leads to stronger thermal effects.

轮轨的相对滑动速度越高，其热效应越明显。

The effects of different sliding speed of magnetic field on friction and wear effects.

研究了不同滑动速度下磁场对摩擦磨损的影响。

Wear rate showing an increasing trend with increasing sliding speed and contact current.

磨耗率随着滑动速度和接触电流的增大呈现增大的趋势。

Basing on the experimental results of longitudinal adhensive coefficient of road surface, this paper discusses the relations between braking process, longitudinal adhensive coefficient of road surface and sliding rate, vehicle speed, road surface roughness, etc.

本文利用路面纵向附着系数的测量结果，对汽车制动过程、路面纵向附着系数与滑移率、车速、路面不平度的关系进行了探讨。