sliding speed的例句大全

to a certain extent, pid and fuzzy control play a good control effect. however, the simulation results show that the fuzzy sliding mode control can better meet the requirements of stability of output power in the case of high wind speed.

PID控制和模糊控制对变桨系统具有一定的控制作用，但从控制效果来看，模糊滑模控制可以更好满足风力发电机组在高风速风况下功率输出稳定的要求，具有更好的动态性能。

the traditional additives only slow the speed of the wear increasing with the sliding distance extension and have only the ability of antiwear, neither have it the wear-self-compensation effect nor make the negative wear.

传统的润滑添加剂只能减缓磨损随行程延长而累积的增加量或尺寸逐步减小的速率，它们对摩擦副只有耐磨功能，而不能产生负磨损，没有磨损自补偿修复功能。

multiple pid, multiple sliding mode and multi-model based fuzzy controllers are introduced to solve the speed, depth, pitch and yaw control problem respectively.

以多模型PID、多模型滑模控制和多模型优化的模糊控制算法解决深度、速度、纵倾和航向控制问题。

Design of a terminal sliding mode speed controller for switched reluctance motor

一类开关磁阻电机的终端滑模控制器设计

A dynamical-integral sliding mode control approach was proposed for the speed controlling of AC servo system.

针对交流伺服系统速度控制问题,提出了一种动态积分滑模控制方法.

Fuzzy Sliding Mode Variable Structure Control for Variable-speed Adjustable-pitch Wind Turbine

变速变桨距风力发电机的模糊滑模变结构控制

The creation and diffusion mechanism of heat, the measure and analysis of the temperature of wear surface under high speed dry sliding were analyzed. The influence of thermal results on tribological performance of friction pair was discussed.

分析了在高速滑动干摩擦过程中热的产生和扩散机理、摩擦温度的测定与分析，讨论了摩擦热效应对配副材料摩擦磨损性能的影晌。

The comprehensive action of these effects, such as low-energy, low-thrust and self-recovering of strength of the slide face, self-dissipating energy of the slide mass, results in low-speed in the sliding of the landslide.

滑体低能效应、滑体低推力效应、滑带（面）强度自行恢复效应和滑体自行消能效应的叠加作用，导致滑坡以低速运移。

Large high speed landslide may produce a very high increase in temperature, and convert the water in sliding zone into vapour, creating a cushion which sustains the slide mass.

大型高速岩质滑坡在启程活动阶段由于高速摩擦产生高温，使滑带水突然汽化，产生巨大的水汽压力，并且可能产生水汽垫层。

And theory research and digital simulation are done for combined control plan which contains middle guide phase with attack angle slide plus vertical unchangeable speed sliding and final phase with proportional guide ballistics, simulation curves are received.

同时提出一种中制导阶段采用定攻角下滑和垂直方向定速下滑，末制导阶段采用比例导引的复合控制方案，并对这一方案作了理论探讨和数字模拟，给出了仿真曲线。

The paper presents a spread spectrum signal acquisition speed sliding correlation method base on FPGA, to address the problem of capture long PN code under low SNR.

文中提出了一种基于FPGA的扩频信号快速滑动相关捕获方法，来解决低信噪比条件下长伪码序列的捕获问题。

The State and Characteristic of New Novel Speed Sliding Bearing

新型高速滑动轴承的发展现状及其特性

Failure analysis and diagnosis on sliding bearing of high speed partial flow pump

高速部分流泵滑动轴承故障分析与诊断

Design of device for measuring the running speed of sliding block

测量滑块运行速度装置的设计

Instant rotational speed, instant torque and displacement of intermediate sliding component of Syndro Self shifting clutches are the key properties to study switch of combined power plant of diesel-gas turbine and gas turbine-gas turbine.

瞬时转速、瞬时扭矩和三S离合器中间滑移件位移测量是研究柴-燃、燃-燃多模块配置联合动力装置主机切换动态特性的关键。

A New Two Speed Control Values in Series and Changes of Two Work Speeds in the Hydraulic Circuit of Power Sliding Feed Table and Design of Its Control System

动力滑台两工进速度换接新回路及其控制系统设计

A New Hydraulic Circuit of Two Work Speeds Change by Series of Two Speed Control Valves And Its Application In Double Pumps Hydraulic System of Modular Machine Tool's Power Sliding Feed Table

串联二调速阀两工进速度换接新回路及其在动力滑台双泵供油液压系统中的应用

On the basis of existing hydraulic circuit, a new valve named Speed Contorl Valve of Two Work Speeds was proposed, which could change two working speeds in the hydraulic circuit to realize the movement of power sliding feed table.

在已有液压回路的基础上，提出了一种新的、用于实现动力滑台运动的二工进调速阀的二工进速度换接回路，给出了其组成图和工作原理。

Based on the mathematical model of the permanent magnet synchronous motor, the sliding surface form according to the error between measured current and observational current, using observed back EMF to calculate estimated speed/ position.

基于永磁同步电机的数学模型，根据实测电流和观测电流之间的误差构成滑模面，应用观测得到的反电动势计算出估计的转速/位置。

On the Guidelines of Editing High Speed Milling for Sliding Guide

论编辑导向滑轨高速铣削加工