stress element的例句大全

An Finite Element method Stress Analysis of Turbine Drum-and-Disk Structure with Tight Fit

带紧度涡轮盘鼓结构的有限元应力分析

A three dimensional finite element analysis on the structure of 4 tilting pad bridge bearing load cell in large turbine generator sets has been made. The influence of boundary condition on the stress or strain field of sensor is studied.

对大型汽轮发电机组四可倾瓦轴承双剪桥式负荷传感器结构进行了三维有限元分析，研究了不同边界条件对传感器结构应力（应变）场的影响。

The Design of Finite Element Analysis Visualization System for Tectonic Stress Field

构造应力场有限元分析可视化系统设计

The method of analyzing the tissue stress with finite element method plays a vital role in tissue engineering.

利用有限单元法进行组织工程中的组织应力分析具有重要意义。

The Three-dimensional Finite Element Stress Analysis of the Mandibular Second Molar Moving Mesially with the Molar Tip-back Bend in Different Angles

不同角度磨牙后倾曲近中移动下颌第二磨牙的有限元分析

Abstract A general nonlinear finite element code has been applied to thermoelastic stress analysis of directionally solidified air cooled turbine blades.

本文利用大型非线性有限元通用程序对定向凝固结晶的气冷叶片进行了热弹性分析。

Finite element for analysing EBW residual stress in titanium alloy plates

钛合金电子束焊接应力分析的有限元模型

The Stress Analysis ′ s Strain Gauge Measurement-Boundary Element Method

应力分析中电测-边界元法

To analyze blade tip exhaust edge fracture failure in stage ⅳ rotor-blade of an engine HP compressor, relative vibration stress and vibration characteristics are calculated by using the finite element software ANSYS.

为了分析某发动机高压压气机Ⅳ级工作叶片叶尖掉角故障，采用ANSYS有限元软件对该级叶片进行了相对振动应力及振动特性计算分析。

Finite Element Numerical Simulation of the Casting Stress Field on the 2 D Vertical Section of the Lathe Bed

机床床身二维纵向截面的铸造应力场有限元数值模拟

The influence of secondary stress on fatigue life was studied by biaxial fatigue test and was contrastively analyzed by finite element method.

利用双轴疲劳试验研究次应力对疲劳寿命的影响，同时进行有限元法对比分析。

In this paper, Ansys finite element software is used to analyze the insulation of thermal bridge in steel structure housing in Hot Summer and Cold Winter Zone, analysis of thermal stress in masonry-infilled steel frames is also involved.

本文主要利用Ansys有限元软件，针对夏热冬冷地区钢结构住宅梁柱热桥节能问题和钢框架-轻质砌体温度应力问题进行了分析。

Impact of thermal stress change on casing by using finite element method

利用有限元法研究热应力变化对套管的影响

Based on the accurate calculation of loads, the current most commonly used prestress methods in thermal production well have been numerically simulated by finite element software ANSYS including conventional cementing, prestressed casing and thermal stress compensator method.

在准确求解载荷的基础上，分别对现阶段在稠油热采井中常使用的常规固井、预应力固井和使用热应力补偿器方式，利用有限元软件ANSYS对井筒模型进行应力数值模拟求解。

Finite element simulation of thermal stress field in cutting LCD glass substrate by laser

液晶显示玻璃基板激光切割热应力场的有限元仿真

Axisymmetric Boundary Element Analysis of Piston Thermal Stress of Diesel Engine

柴油机活塞热应力轴对称边界元数值分析

The paper use finite element analysis method analysis the thermal impact of PCBA during the reflow soldering, and building the temperature and stress distribution model.

本文利用有限元法对PCB组件在再流焊过程中的受热进行分析，建立瞬态温度场和应力场模型。

The finite element code LS_DYNA is used to investigate the response of the axisymmetry cylindrical shell under the thermal impact, and the curves of displacement vs time and that of stress vs time are obtained.

最后利用有限元程序LS-DYNA对轴对称圆柱壳受高速热冲击作用进行了计算机仿真分析，得到了位移时间曲线和单元的应力时间曲线，同文献已有的结果吻合的较好。

In view of the lining concrete engineering of Xiluodu hydropower station, 3-dimensional finite element method is used to analyze thermal stress sensitivity of the surrounding rock deformation modulus.

针对溪洛渡水电站导流洞衬砌混凝土工程，采用三维有限元法分析了围岩变形模量变化对温度应力影响的敏感性。

A corresponding computer program by using finite element methed is coded in FORTRAN 77 and is implemented on microcomputers. Numerical results show that the thermal stress and material softening irradiated laser beam will induce the catastrophic buckling failure of the pre compressed cylindrical shell.

数值计算结果表明，激光照射区域产生的热应力和材料软化将导致处于正常工作状态的轴压圆柱壳发生灾难性的热屈曲破坏。