surface load的例句大全

Then, the mathematics model of calculating the surface load and point load in the design of aircraft structure static load test using aircraft surface model is established.

其次结合飞机的曲面外形，建立了飞机结构静力试验设计中的分布式载荷和集中式载荷的演算数学模型。

For inclined-tube sedimentation design, the parameter of tank can be determined by inclined-tube parameters, discharge and surface load.

对于斜板（斜管）沉淀池设计，则主要通过选定的斜板（斜管）参数、流量和表面负荷等来确定沉淀池的各参数。

Based on the established equivalent numerical analysis model of sliding plug door made from composite material and taking use of ANSYS numerical value, we simulate the response of sliding plug door of high-speed train under surface load of 6000 Pa, and validate the simulation result through experiment.

依据已建立的复合材料塞拉门数值分析等效模型，利用ANSYS数值模拟了高速列车塞拉门在6000Pa面静载荷下的响应，并通过实验对模拟结果进行了验证。

Below figure shows the relation between fumace temperatures, element temperature and element surface load under the condition that the element radiation isn't obstructed.

下图示出了元件辐射在不受阻碍情况下的炉温、件温度与表面负荷之间的关系。

Presently, the complete loading calculation mode is widely used as the design method of the metro station, but the vertical load from the temporary road surface system isn't taken into account.

目前，我国地铁车站设计中普遍采用的一次加载的计算模式，也没有考虑盖挖施工临时路面体系传递的竖向荷载。

The polypropylene fiber concrete has excellent tensile performance, crack resist-ance, ductility and load-carrying capacity and especially the polypropylene fibers can contribute to good control of early cracking in the surface of concrete.

聚丙烯纤维混凝土具有优良的抗拉性能、抗裂度、韧性和承载力，特别是对水泥混凝土表面的早期开裂控制起到了良好的作用。

This article mainly analyses the factors that affect the precise indexer life, touching surface pressure, basic motion load and temperature factor for example.

着重分析影响精密分度装置寿命的接触表面压力，基本动载荷，温度系数等因素。

And the influences of axle load and vehicle speed and tire pressure and the thickness of the surface layer on the dynamic response of the inverse structure asphalt pavement were studied.

深入研究了轴重、速度、胎压和面层厚度对倒装结构动力响应的影响。

Under intermittent operation condition, temperature recovery at night and load trace at the end of running period of three ground surface forms are compared.

对间歇运行工况下，三种上垫面形式下的夜间恢复情况和运行周期末的负荷痕迹值进行了对比分析。

With the load increased, however, the friction reduction weakened significantly, this shows that it is difficult to reduce friction using surface texture under the high test load.

但是，随着试验载荷的增大，这种减摩效果明显减弱，显示出在高载荷条件下利用表面织构降低摩擦的难度要高于低载荷条件。

It is demonstrated that the radiation surface temperature and overall structure strength of the straps under the real thermal load ( 0.2MW) satisfy the design requirements.

论证了在实际工况热载荷条件（0.2MW）下，电流带辐射面温度及电流带整体结构强度满足设计要求。

ST bumper used to resist shock is a pivotal part in railway vehicle transportation. As primary load-transfer component of this part, thrust cone required very high precision and surface quality.

ST型缓冲器是铁路车辆运输过程中用于抗冲击的关键部件，推力锥作为其中的主要传力零件，其精度和表面质量要求都非常高。

Dynamic Response of Elastic Layer on Stiff Foundation under Time Harmonic Surface Vertical Concentrated Load

刚性基础上的弹性层在表面垂直集中简谐载荷作用下的动力响应

A set of one-dimensional regular integral equations is derived for calculating the dynamic response of elastic layer on stiff foundation under time harmonic surface vertical concentrated load. And the numerical solution of the integral equation is obtained.

导出了刚性基础上的弹性层在表面垂直集中简谐载荷作用下动力响应问题的一维非奇异积分方程组，并求得了数值解。

Before the indenter tip touched the surface of the sample, the displacement value measured by a capacitive displacement sensor was the output of the loading mechanism without load.

在压头尖与试样表面接触前，由电容测微仪测得的位移值是加载装置空载下的输出值；

The surface tension of load fluid QY with 0.5% surfactant added and load fluid 851 is of 36.3 and 47.9 mN/ m and the interfacial tension-2.1 and 6.7 mN/ m, respectively.

表面活性剂加量为0.5%的压井液QY和压井液851的表面张力分别为36.3和47.9mN/m，界面张力分别为2.1和6.7mN/m。

Under offset load, the stresses around the crack tip and the surface deflection in the pavement with cracks have a great increase compared with that without cracks.

在偏荷载作用下，含表面裂缝的路面结构裂缝尖端的应力以及路表弯沉较无裂缝结构有很大的增长。

And when the indenter tip touched the surface of the sample, the trend of the displacement values measured by the sensor would depart from that of the displacement values of indenter having no load.

而当压头尖与试样表面接触后，压头与试样之间将产生作用力，使电容测微仪的测量值偏离加载装置空载下的输出曲线趋势。

Through the three-dimensional finite element analysis modeling, the text analyzes the influencing rule and outstanding function of the load stress 、 the thermal stress and coupled stress to asphalt surface course's thickness 、 base's thickness 、 modulus and the foundation's modulus.

利用三维有限元模型，分析了沥青面层厚度、基层厚度、基层模量和地基模量等参数对刚性基层的荷载应力、温度应力及其两者之间的耦合应力的影响规律及其显著性。

Analysis of Thermal Load for Die Cavity Surface

锻模型腔表面热负荷分析